Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0074466 VALVE BODY ASSEMBLY A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 35418 1.INSTALL MANUAL VALVE

a.

Coat the manual valve with ATF and install it to the transmission valve body assembly.


Hide 35410 2.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.

Coat the O-ring of the transmission wire with ATF.


b.
C136689
2,2.177 1.469,2.844 1.469,2.844 0.875,2.344 false 1.635,2.177 1.469,2.844 1.469,2.844 1.24,2.198 false 2.073,0.969 2.5,0.198 2.5,0.198 2.573,0.198 false 1.344,0.958 1.729,0.24 1.729,0.24 1.792,0.24 false 0.917,0.896 1.188,0.219 1.188,0.219 1.25,0.219 false 0.49,1.354 0.25,0.948 false 0.479,2.063 0.281,2.365 false 2.313,2.177 2.708,2.719 2.708,2.719 2.792,2.719 false 2.76,1.583 2.885,2 2.885,2 2.969,2 false 0.052,2.479 0.323,2.656 0.271,0.177 10 false (*a) 2.615,0.115 2.76,0.271 0.146,0.156 10 false A 1.406,2.844 1.552,3 0.146,0.156 10 false B 0.094,0.865 0.24,1.021 0.146,0.156 10 false D 1.292,0.125 1.438,0.281 0.146,0.156 10 false C 0.125,2.302 0.271,2.458 0.146,0.156 10 false E 2.99,1.906 3.135,2.063 0.146,0.156 10 false B 1.813,0.135 1.958,0.292 0.146,0.156 10 false B 2.896,2.073 3.146,2.25 0.25,0.177 10 true (*a) 2.823,2.635 2.969,2.792 0.146,0.156 10 false B
*a Positioning Bolt


Confirm that the manual valve lever is positioned as shown in the illustration and install the transmission valve body assembly to the automatic transaxle assembly with the 11 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

Bolt length:
Bolt A:

25 mm (0.984 in.)

Bolt B:

30 mm (1.18 in.)

Bolt C:

35 mm (1.38 in.)

Bolt D:

45 mm (1.77 in.)

Bolt E:

55 mm (2.17 in.)


NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.

·

Be sure to insert the pin of the manual valve lever into the groove on the end of the manual valve.

·

First, temporarily tighten the bolts marked (*a) in the illustration because they are positioning bolts.




Hide 35330 3.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted or pinched.



b.

Install the valve body oil strainer assembly to the transmission valve body assembly with the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 35106D 4.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C134963
2.906,0.219 1.885,0.219 1.885,0.219 1.885,1.417 false 2.448,1 2.448,0.219 false 2.969,0.135 3.135,0.302 0.167,0.167 10 false *1
*1 Magnet


Install the 2 magnets onto the automatic transaxle oil pan sub-assembly as shown in the illustration.


b.

Install a new gasket to the automatic transaxle oil pan sub-assembly.


c.
C274789

Install the automatic transaxle oil pan sub-assembly to the automatic transaxle assembly with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.
C274790

Clean and degrease the bolt and the installation hole in the automatic transaxle assembly.


e.

Apply adhesive to the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.

Install the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:
·

In order to ensure proper sealing of the automatic transaxle oil pan sub-assembly bolt, apply adhesive to the bolt and install it within 10 minutes of adhesive application.

·

Completely remove any oil or grease from the contact surface of the transaxle case sub-assembly and automatic transaxle oil pan sub-assembly with the gasket before installation.