Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › TORQUE CONVERTER AND DRIVE PLATE
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0074473 TORQUE CONVERTER AND DRIVE PLATE G

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 1.INSPECT TORQUE CONVERTER ASSEMBLY

a.

Inspect the one-way clutch.

i.
C151051
1.25,0.76 1.26,0.74 false
V100135

Difficult
V100136

Smooth


Press on the splines of the stator with a finger and rotate it. Check that it rotates smoothly when turned clockwise and rotates with difficulty when turned counterclockwise.

If necessary, clean the torque converter assembly and recheck the one-way clutch.

Replace the torque converter assembly if the one-way clutch still fails the inspection.



b.
C274827
0.229,0.198 0.677,0.448 0.448,0.25 10 false *a
*a Sample showing maximum allowable amount of powder in ATF


Inspect the torque converter assembly.

If any of the following problems are present, replace the torque converter assembly.

Malfunction:
·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch turns smoothly or locks in both directions.

·

The amount of powder in the ATF is more than the sample shown in the illustration (refer to the sample).


HINT:

The sample shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF that was removed from a torque converter assembly.



c.

Replace the ATF in the torque converter assembly.

HINT:

If the ATF is discolored or has a foul odor, stir the ATF in the torque converter assembly and drain it before replacing the ATF.



d.
C011090

Clean and check the oil cooler and oil pipe line.

HINT:
·

If the torque converter assembly is inspected or the ATF is replaced, it is necessary to clean the oil cooler and oil pipe line.

·

Apply compressed air of 196 kPa (2.0 kgf/ cm2, 28 psi) into the inlet hose.

·

If a large amount of powder is found in the ATF, add new ATF using a bucket pump and clean the oil cooler and oil pipe line again.

·

If the ATF is cloudy, inspect the oil cooler.




e.
D025368
1.729,1.885 2.208,1.865 false 2.26,1.76 2.448,1.958 0.188,0.198 10 false *c 0.49,0.167 0.76,0.333 0.271,0.167 10 false *a 1.531,0.167 1.802,0.333 0.271,0.167 10 false *b
*a CORRECT
*b INCORRECT
*c Bottom is damaged


Prevent deformation of the torque converter assembly and damage to the oil pump gear.

NOTICE:

Make sure that all of the bolts are the same length and that the specified bolts are used.


HINT:

If there is any damage to the tip of a bolt for the torque converter assembly or to the bottom of a bolt hole, replace the bolt and torque converter assembly.



Hide 2.INSPECT DRIVE PLATE

a.
C238929
1.675,0.338 1.803,0.493 0.129,0.155 10 1 1.253,1.045 1.382,1.2 0.129,0.155 10 2 1.818,1.958 1.947,2.114 0.129,0.155 10 3 2.674,1.932 2.803,2.087 0.129,0.155 10 4 2.881,1.213 3.009,1.368 0.129,0.155 10 5 2.443,0.525 2.571,0.68 0.129,0.155 10 6
V100144

Measurement Point


Check the drive plate for damage.


b.

Set up a dial indicator and measure the runout at the 6 areas on the drive plate surface that contact the torque converter assembly.

Maximum runout:

0.30 mm (0.0118 in.)


HINT:
·

If the runout is more than the maximum or the drive plate is damaged, replace the drive plate.

·

If installing a new drive plate, confirm that the spacers are oriented properly before tightening the bolts.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>REAR CRANKSHAFT OIL SEAL>INSTALLATION