Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL PUMP
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0074475 OIL PUMP A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  REASSEMBLY  


PROCEDURE

Hide 35301A 1.INSTALL FRONT OIL PUMP OIL SEAL

a.
C188149
1.313,2.052 1.042,2.052 false 2.438,1.333 2.333,1.333 2.333,1.333 1.781,0.906 false 2.49,1.281 2.99,1.573 0.5,0.292 10 false SST 0.719,1.958 1.01,2.115 0.292,0.156 10 false SST

Using SST and a hammer, install a new front oil pump oil seal to the front oil pump body sub-assembly.

SST
09350-32014  (09351-32140)

Oil seal driven in depth:

-0.25 to 0.25 mm (-0.00984 to 0.00984 in.)



b.

Coat the lip of the front oil pump oil seal with MP grease.


Hide 35301B 2.INSTALL FRONT OIL PUMP BODY O-RING

a.
C138278

Coat a new front oil pump body O-ring with ATF and install it to the front oil pump body sub-assembly.

NOTICE:

Ensure that the front oil pump body O-ring is not twisted.



Hide 35322 3.INSTALL FRONT OIL PUMP DRIVEN GEAR

a.
C138277

Coat the front oil pump driven gear with ATF and install it to the front oil pump body sub-assembly with the marked side facing up.


Hide 35321 4.INSTALL FRONT OIL PUMP DRIVE GEAR

a.
C138276

Coat the front oil pump drive gear with ATF, and install it to the front oil pump body sub-assembly with the marked side facing up.


Hide 35370 5.INSTALL STATOR SHAFT ASSEMBLY

a.
C138275
1.45,2.46 1.6,2.625 0.15,0.165 10 B 0.766,1.177 0.916,1.342 0.15,0.165 10 A 1.005,0.553 1.155,0.718 0.15,0.165 10 A 1.659,0.194 1.809,0.36 0.15,0.165 10 A 2.295,0.507 2.445,0.672 0.15,0.165 10 A 2.579,0.975 2.73,1.14 0.15,0.165 10 A 2.554,1.613 2.704,1.778 0.15,0.165 10 A 2.183,2.087 2.333,2.252 0.15,0.165 10 A 1.707,2.207 1.858,2.372 0.15,0.165 10 A 1.004,1.868 1.143,2.033 0.14,0.165 10 A 2.226,2.681 2.376,2.846 0.15,0.165 10 B 2.438,3.298 2.588,3.463 0.15,0.165 10 B 2.377,4.008 2.527,4.173 0.15,0.165 10 B 0.875,3.831 1.025,3.996 0.15,0.165 10 B 0.887,3.041 1.038,3.206 0.15,0.165 10 B 1.339,4.248 1.489,4.413 0.15,0.165 10 B

Align each knock pin of the stator shaft assembly with the holes in the front oil pump body sub-assembly and install the stator shaft assembly to the front oil pump body sub-assembly.


b.

Using a "TORX" socket wrench (T30), install the 16 bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)

Bolt Length:
Bolt A:

14 mm (0.551 in.)

Bolt B:

26 mm (1.02 in.)



Hide 35035 6.INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY