Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM2030EQ _52 Drivetrain _014644 DRIVE SHAFT / PROPELLER SHAFT _0074480 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 43420 1.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

a.

Coat the spline of the front drive inboard joint assembly with ATF WS.


b.

Coat the lip of the transaxle case oil seal with MP grease.


c.
C165536

Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

NOTICE:
·

Face the end gap of the front drive shaft hole snap ring LH downward.

·

Do not damage the transaxle case oil seal.

·

Do not damage the front axle inboard joint boot.

·

Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring LH.



HINT:

Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



d.
C240136C01
2.771,0.813 3.115,0.813 3.115,0.813 3.115,1.74 false 2.938,1.135 3.115,1.135 false 3.031,1.75 3.26,2.01 0.229,0.26 10 false *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.

NOTICE:

Be careful not to damage the front axle outboard joint boot or speed sensor rotor.



Hide 43410 2.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

a.

Coat the spline of the front drive inboard joint assembly with ATF WS.


b.

Coat the lip of the front transaxle case oil seal with MP grease.


c.

Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.


d.

Install the front drive shaft assembly RH.

NOTICE:
·

Do not damage the front transaxle case oil seal.

·

Do not damage the front axle inboard joint boot.

·

When inserting the front drive shaft assembly RH, keep it level.




e.
C239399

Install the bearing bracket hole snap ring and a new bolt.

Torque:
32 N*m (330 kgf*cm, 24 ft.*lbf)


f.
C240137C02
0.667,0.813 0.323,0.813 0.323,0.813 0.323,1.656 false 0.51,1.146 0.323,1.146 false 0.271,1.667 0.438,1.823 0.167,0.156 10 *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.

NOTICE:

Be careful not to damage the front axle outboard joint boot or speed sensor rotor.



Hide 48069 3.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 45470 4.CONNECT TIE ROD ASSEMBLY

Hide 89543 5.INSTALL FRONT SPEED SENSOR

Hide 48810 6.INSTALL FRONT STABILIZER LINK ASSEMBLY

Hide 43502H 7.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new axle shaft nut using a non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new drive shaft.

·

Keep the threaded parts free of oil and foreign matter.




b.
C165538

Using a socket wrench (30 mm), install the front axle shaft nut.

Torque:
294 N*m (2998 kgf*cm, 217 ft.*lbf)


c.

Using a chisel and a hammer, stake the front axle shaft nut.


Hide 8.INSTALL FRONT WHEELS

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 53737B 10.INSTALL FRONT FENDER APRON SEAL LH

Hide 53736 11.INSTALL FRONT FENDER APRON SEAL RH

Hide 51442C 12.INSTALL ENGINE UNDER COVER LH

Hide 53852K 13.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 51441C 14.INSTALL ENGINE UNDER COVER RH

Hide 53851Z 15.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)