Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER(for RHD)
RM2030EQ _54 Brake _014651 BRAKE SYSTEM (OTHER) _0074515 BRAKE MASTER CYLINDER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for RHD)  INSTALLATION  


PROCEDURE

Hide 47201B 1.INSTALL BRAKE MASTER CYLINDER O-RING

a.

Install a new brake master cylinder O-ring to the brake master cylinder sub-assembly.


Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

NOTICE:

When installing a new brake master cylinder sub-assembly, remove the protectors from the master cylinder piston and outlet ports.


a.
C243056C01
2.135,1.563 2.229,1.688 0.094,0.125 6 .
V100145

Apply Grease


Apply a light layer of a grease enclosed with a new brake master cylinder sub-assembly or lithium soap base glycol grease to the circumference of the brake master cylinder sub-assembly and inner surface of the brake booster assembly as shown in the illustration.


b.
C239870C01
2.792,3.698 3.01,3.698 false 3.031,3.615 3.292,3.854 0.26,0.24 10 *1
*1 Master Cylinder Piston


Install the brake master cylinder sub-assembly and vacuum check valve bracket to the brake booster assembly with the 2 nuts.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its reservoir when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or its tip faces downward (the master cylinder piston faces upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of cloth and then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Do not kink or damage the brake lines.

·

Do not allow brake lines to twist and interfere with other parts or vehicle body during flexible hose tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines.




c.

Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow brake lines to twist and interfere with other parts or vehicle body during flexible hose tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




d.

Connect the reservoir level switch connector.


Hide 3.BLEED BRAKE SYSTEM

Hide 55702A 4.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

Install the front outer cowl top panel sub-assembly with the 10 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.


Hide 5.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY