Home › Brake › BRAKE (REAR) › REAR BRAKE › 2012.02–2015.04
RM2030EQ _54 Brake _014653 BRAKE (REAR) _0074520 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C143446C01
2.083,1.115 1.354,1.5 1.354,1.5 2.021,1.01 true 1.188,1.438 1.417,1.635 0.229,0.198 10 false *a
*a Matchmark


Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.

NOTICE:

When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 42491 2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Install the parking brake shoe adjusting hole plug.


Hide 47722A 3.INSTALL DISC BRAKE CYLINDER MOUNTING

a.

for PBR Made:

i.
C246339

Install the disc brake cylinder mounting with the 2 bolts.

Torque:
47 N*m (475 kgf*cm, 34 ft.*lbf)



b.

for ADVICS Made:

i.
C243125

Install the disc brake cylinder mounting with the 2 bolts.

Torque:
62 N*m (630 kgf*cm, 46 ft.*lbf)



Hide 47775D 4.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.

for PBR Made:

i.
C248020C01
0.885,1.188 0.896,1.188 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the seal surfaces of 2 new rear disc brake bushing dust boots.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



ii.

Apply a light layer of lithium soap base glycol grease to the sliding part and the seal surface of the rear disc brake cylinder slide pin.


iii.

Install the rear disc brake bushing dust boot to each rear disc brake cylinder slide pin.



b.

for ADVICS Made:

i.
C239548C02
1.375,0.802 1.365,0.792 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



ii.
C243124

Install the 2 rear disc brake bushing dust boots to the disc brake cylinder mounting.



Hide 47715C 5.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.

for PBR Made:

i.

Install the 2 rear disc brake cylinder slide pins to the disc brake cylinder mounting.


ii.

Install the 2 rear disc brake bushing dust boots to the groove of the rear brake cylinder mounting.



Hide 6.INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSHING

a.

for ADVICS Made:

i.
C211757C07
1.74,1.156 1.74,1.146 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the rear disc brake cylinder slide pin.


ii.

Install a new rear disc brake cylinder slide bushing to the rear disc brake cylinder slide pin.



Hide 47814 7.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN (for Lower Side)

a.

for ADVICS Made:

i.
C211758C07
1.24,0.927 1.229,0.927 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the rear disc brake cylinder slide pin.


ii.
C243123

Install the rear disc brake cylinder slide pin to the disc brake cylinder mounting.


iii.

Push the rear disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.



Hide 47814 8.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN (for Upper Side)

a.

for ADVICS Made:

i.
C211759C06
1.333,0.875 1.344,0.875 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the rear disc brake cylinder slide pin.


ii.
C243122

Install the rear disc brake cylinder slide pin to the disc brake cylinder mounting.


iii.

Push the rear disc brake cylinder slide pin into the rear disc brake bushing dust boot to engage the pin to the boot.



Hide 47716A 9.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.

for ADVICS Made:

i.
C273541C01
0.833,0.521 1.052,0.521 1.052,0.521 1.24,0.646 false 2.292,1.635 2.625,1.833 2.625,1.833 2.844,1.833 false 0.677,0.469 0.99,0.625 0.313,0.156 10 *1 2.885,1.781 3.198,1.938 0.313,0.156 10 *2 1.323,0.104 1.479,0.302 0.156,0.198 10 A 2.813,1.063 2.969,1.26 0.156,0.198 10 b 2.792,1.323 2.948,1.521 0.156,0.198 10 B 1.885,0.083 2.042,0.281 0.156,0.198 10 a
*1 Rear Disc Brake Pad Support Plate
*2 Disc Brake Cylinder Mounting


Install the 2 rear disc brake pad support plates to the disc brake cylinder mounting.

NOTICE:

Firmly push to install the rear disc brake pad support plate and disc brake cylinder mounting against each other so that there is no clearance between the surfaces A and a, and B and b.




Hide 04946 10.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.

for ADVICS Made:

i.
C239557

Install the pad wear indicator plate to each rear disc brake pad.

NOTICE:

Install each pad wear indicator plate in the correct position and direction.



ii.
C239556C02
0.979,1.479 0.979,1.49 false
V100155

Disc Brake Grease


Apply disc brake grease to the inside of the rear disc brake anti-squeal shims.


iii.
C239558

Install the rear disc brake anti-squeal shim to each rear disc brake pad with pad wear indicator plate.

NOTICE:
·

Disc brake grease may seep out slightly from the areas where the rear disc brake anti-squeal shims are installed.

·

Make sure that disc brake grease is not applied onto the lining surface.





Hide 04466 11.INSTALL REAR DISC BRAKE PAD

a.

for PBR Made:

i.
C246371C01
2.427,2.854 2.594,3.021 2.594,3.021 2.708,3.021 false 0.656,0.271 0.844,0.427 0.188,0.156 10 false *A 0.667,1.906 1.01,2.156 0.344,0.25 10 false *B 2.729,2.927 2.906,3.104 0.177,0.177 10 false *1
*A Outer Side
*B Inner Side
*1 Pad Wear Indicator


Install the 2 rear disc brake pads to the disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.




b.

for ADVICS Made:

i.

Install the 2 rear disc brake pads with rear disc brake anti-squeal shim kit to the disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.




Hide 47850 12.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.

for PBR Made:

i.
C249611C01
2.108,0.457 2.276,0.609 0.168,0.152 10 *a 3.064,0.825 3.232,0.977 0.168,0.152 10 *b
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin, and install the rear disc brake cylinder assembly to the disc brake cylinder mounting with the 2 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)

NOTICE:

Make sure that the rear brake pad springs do not get caught at the point on the rear disc brake cylinder assembly shown in the illustration.




b.

for ADVICS Made:

i.
C239570C01
2.26,0.448 2.531,0.688 0.271,0.24 10 *b 2.74,1.833 3.01,2.052 0.271,0.219 10 *a
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin, and install the rear disc brake cylinder assembly to the disc brake cylinder mounting with the 2 bolts.

Torque:
27 N*m (270 kgf*cm, 20 ft.*lbf)

NOTICE:

Make sure that the rear brake pad springs do not get caught at the point on the rear disc brake cylinder assembly shown in the illustration.




Hide 47319F 13.CONNECT REAR FLEXIBLE HOSE

a.

for PBR Made:

i.
C246335C01
0.644,1.07 0.801,1.219 0.157,0.15 10 *a 2.01,1.153 0.826,1.153 false
*a Lock Hole


Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and 2 new gaskets.

Torque:
30 N*m (305 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the flexible hose lock securely into the lock hole in the disc brake cylinder.




b.

for ADVICS Made:

i.
C243121C02
1.885,0.979 2.458,1.542 2.458,1.542 2.656,1.542 true 2.688,1.458 2.865,1.615 0.177,0.156 10 *a
*a Lock Hole


Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
33 N*m (340 kgf*cm, 25 ft.*lbf)

NOTICE:

Install the flexible hose lock securely into the lock hole in the disc brake cylinder.




Hide 15.ADJUST PARKING BRAKE

Hide 16.INSTALL REAR WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)