1.INSPECT PARKING BRAKE PEDAL TRAVEL
Fully depress the parking brake pedal to engage the parking brake.
Depress the pedal again to disengage the parking brake.
for PBR Made:
Slowly depress the parking brake pedal using the specified force, and count the number of clicks.
7 to 10 notches at 300 N (31 kgf, 67.5 lbf)
9 to 12 notches at 300 N (31 kgf, 67.5 lbf)
If the parking brake pedal travel is not as specified, adjust the parking brake shoe clearance and parking brake pedal travel.
for ADVICS Made:
Slowly depress the parking brake pedal using the specified force, and count the number of clicks.
7 to 10 notches at 300 N (31 kgf, 67.5 lbf)
If the parking brake pedal travel is not as specified, adjust the parking brake shoe clearance and parking brake pedal travel.
2.ADJUST PARKING BRAKE PEDAL TRAVEL (for LHD)
for PBR Made:
Completely release the parking brake pedal.
| *1 | Lock Nut |
| *2 | Adjusting Nut |
Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
Remove the rear wheels.
Separate the rear disc brake caliper assembly.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL
Remove the parking brake shoe adjusting hole plug.
Remove the rear disc.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT
Measure the brake shoe diameter as shown in the illustration.
189.6 to 189.7 mm (7.46 to 7.47 in.)
| *1 | Nut |
If the shoe diameter is not as specified, adjust it by turning the nut.
The gap between the adjusting nut and screw must not exceed 5 mm (0.197 in.). If the gap is set to this specification and the shoe diameter is less than specified, replace the parking brake shoe. If the lining thickness is less than 1.5 mm (0.0591 in.) or exhibits uneven wear, replace the parking brake shoe.
5 mm (0.197 in.) max
Install the rear disc.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT
Check for drag. Spin the rotor and ensure there is no drag from the parking brake shoe.
If there is drag, apply and release the parking brake pedal and retest. If drag is still present, remove the disc, remeasure and readjust the shoe diameter and centralize the shoe. Reassemble the disc and recheck for drag.
Install the parking brake shoe adjusting hole plug.
Install the rear disc brake caliper assembly.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT
Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.
7 to 10 notches at 300 N (31 kgf, 67.5 lbf)
Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.
Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.
Check that the parking brake does not drag.
Install the rear wheels.
for ADVICS Made:
Completely release the parking brake pedal.
| *1 | Lock Nut |
| *2 | Adjusting Nut |
Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
Remove the rear wheels.
Temporarily install the hub nuts to the hub bolts.
Securely install the hub nuts to the rear disc.
Remove the parking brake shoe adjusting hole plug.
|
Expand |
|
Contract |
Turn the shoe adjuster and expand the shoes until the disc locks.
Turn and contract the shoe adjuster until the disc can rotate smoothly.
Returns 8 notches.
Check that there is no brake drag against the shoes.
Install the parking brake shoe adjusting hole plug.
Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.
7 to 10 notches at 300 N (31 kgf, 67.5 lbf)
Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.
Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.
Check that the parking brake does not drag.
Remove the hub nuts from the hub bolts.
Install the rear wheels.
3.ADJUST PARKING BRAKE PEDAL TRAVEL (for RHD)
for PBR Made:
Completely release the parking brake pedal.
| *1 | Lock Nut |
| *2 | Adjusting Nut |
Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
Remove the rear wheels.
Separate the rear disc brake caliper assembly.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL
Remove the parking brake shoe adjusting hole plug.
Remove the rear disc.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT
Measure the brake shoe diameter as shown in the illustration.
189.6 to 189.7 mm (7.46 to 7.47 in.)
| *1 | Nut |
If the shoe diameter is not as specified, adjust it by turning the nut.
The gap between the adjusting nut and screw must not exceed 5 mm (0.197 in.). If the gap is set to this specification and the shoe diameter is less than specified, replace the parking brake shoe. If the lining thickness is less than 1.5 mm (0.0591 in.) or exhibits uneven wear, replace the parking brake shoe.
5 mm (0.197 in.) max
Install the rear disc.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT
Check for drag. Spin the rotor and ensure there is no drag from the parking brake shoe.
If there is drag, apply and release the parking brake pedal and retest. If drag is still present, remove the disc, remeasure and readjust the shoe diameter and centralize the shoe. Reassemble the disc and recheck for drag.
Install the parking brake shoe adjusting hole plug.
Install the rear disc brake caliper assembly.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT
Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.
9 to 12 notches at 300 N (31 kgf, 67.5 lbf)
Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.
Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.
Check that the parking brake does not drag.
Install the rear wheels.
for ADVICS Made:
Completely release the parking brake pedal.
| *1 | Lock Nut |
| *2 | Adjusting Nut |
Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
Remove the rear wheels.
Temporarily install the hub nuts to the hub bolts.
Securely install the hub nuts to the rear disc.
Remove the parking brake shoe adjusting hole plug.
|
Expand |
|
Contract |
Turn the shoe adjuster and expand the shoes until the disc locks.
Turn and contract the shoe adjuster until the disc can rotate smoothly.
Returns 8 notches.
Check that there is no brake drag against the shoes.
Install the parking brake shoe adjusting hole plug.
Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.
7 to 10 notches at 300 N (31 kgf, 67.5 lbf)
Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.
Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.
Check that the parking brake does not drag.
Remove the hub nuts from the hub bolts.
Install the rear wheels.
4.INSPECT BRAKE WARNING LIGHT
When operating the parking brake pedal, check that the brake warning light illuminates.
The brake warning light always illuminates at the first click.