Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM2030EQ _55 Steering _014657 STEERING GEAR / LINKAGE _0074538 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to align the front wheels straight ahead when removing and installing the steering gear assembly.

·

When disconnecting the steering intermediate shaft assembly and the pinion shaft of the steering gear assembly, be sure to place matchmarks before servicing.



PROCEDURE

Hide 1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.REMOVE FRONT WHEELS

Hide 3.SECURE STEERING WHEEL

a.
C246341

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 45220 4.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C238511C01
1.49,2.781 0.823,2.854 0.823,2.854 1.542,2.854 true 0.625,2.771 0.792,2.927 0.167,0.156 10 *a
*a Matchmark


Put matchmarks on the steering intermediate shaft assembly and steering link assembly.


b.

Remove the bolt.


c.

Separate the steering intermediate shaft assembly from the steering link assembly.


Hide 45470 5.SEPARATE TIE ROD ASSEMBLY LH

a.
C238512

Remove the cotter pin and nut.


b.
C238513N03
2.561,1.388 2.855,1.538 0.293,0.151 10 SST 2.72,1.254 2.72,1.392 false

Install SST to the tie rod assembly LH.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the lower ends of the tie rod assembly LH and SST are aligned.



c.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.



d.

Using SST, separate the tie rod assembly LH from the steering knuckle.

C238514C02
0.99,0.604 1.323,0.281 1.323,0.281 1.438,0.281 true 0.917,2.01 0.917,1.646 0.917,1.646 0.76,1.646 false 3.76,2.073 3.76,2.156 3.76,2.156 4.01,2.156 true 1.438,0.198 1.594,0.354 0.156,0.156 10 *a 6.625,1.823 6.781,1.979 0.156,0.156 10 *b 6.667,2.167 6.823,2.323 0.156,0.156 10 *b 0.625,1.583 0.781,1.729 0.156,0.146 10 *1 1.677,2.302 1.802,2.458 0.125,0.156 10 A 1.688,2.094 1.813,2.25 0.125,0.156 10 B 4.052,2.073 4.354,2.219 0.302,0.146 10 SST
*1 Center Nut - -
*a String *b Grease Application Area
V100136

Place the wrench here. - -


SST
09960-20010  (09961-02010)

CAUTION:

Apply grease to the bolt threads and the tip of SST.


NOTICE:
·

Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the dust cover may be damaged.


·

Be sure to place the wrench on the part indicated in the illustration.


·

Do not damage the front disc brake dust cover.


·

Do not damage the ball joint dust cover.


·

Do not damage the steering knuckle.




Hide 45460 6.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 7.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 48829A 8.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 9.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48811 10.REMOVE FRONT STABILIZER BAR

Hide 11.REMOVE STEERING LINK ASSEMBLY

a.
C238515

Remove the 2 bolts, 2 nuts and steering link assembly.

NOTICE:

Keep the nut from rotating while turning the bolt because the nut has its own stopper.



Hide 12.SECURE STEERING LINK ASSEMBLY

a.
C238516C01
1.448,1.042 1.677,1.271 1.677,1.271 1.865,1.271 false 1.167,0.729 1.167,0.396 1.167,0.396 0.573,0.396 false 1.906,1.198 2.198,1.427 0.292,0.229 10 *1 0.281,0.323 0.823,0.625 0.542,0.302 10 SST
*1 Protective Tape


Using SST, secure the steering link assembly in a vise.

SST
09612-00012  

HINT:

Tape SST before use.



Hide 45470 13.REMOVE TIE ROD ASSEMBLY LH

a.
C238518C04
1.24,1.042 1.24,1.563 true 1.021,1.042 1.021,1.26 1.021,1.26 1.24,1.26 true 1.156,1.573 1.313,1.719 0.156,0.146 10 *a
*a Matchmark


Put matchmarks on the tie rod assembly LH and the steering rack end sub-assembly.


b.

Remove the tie rod assembly LH and lock nut.


Hide 45460 14.REMOVE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.