Home › Power Source / Network › 2GR-FE BATTERY / CHARGING › GENERATOR
RM2030EQ _57 Power Source / Network _014661 2GR-FE BATTERY / CHARGING _0074570 GENERATOR A

2GR-FE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27039 1.REMOVE GENERATOR REAR END COVER

a.
A128071

Remove the 3 nuts and generator rear end cover.


Hide 27387B 2.REMOVE GENERATOR TERMINAL INSULATOR

a.
A128072

Remove the generator terminal insulator from the generator coil.


Hide 27370 3.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A128073

Remove the 2 screws and generator brush holder from the generator coil.


Hide 27360 4.REMOVE GENERATOR COIL ASSEMBLY

a.
A128074

Remove the 4 bolts.


b.
A118275
0.656,0.542 1.094,0.323 false 2.135,0.74 2.552,0.74 false 1.146,0.24 1.458,0.385 0.313,0.146 10 false SST 2.646,0.094 2.833,0.24 0.188,0.146 10 false *a 2.625,0.656 2.938,0.802 0.313,0.146 10 false SST 0.635,1.75 0.823,1.896 0.188,0.146 10 false *b
*a Turn
*b Hold


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


c.
A293820

Remove the generator washer.


Hide 27415 5.REMOVE GENERATOR PULLEY WITH CLUTCH

a.
A240513

Using a screwdriver, remove the generator pulley cap.

NOTICE:

Do not reuse the generator pulley cap.



b.

Mount the generator drive end frame in a vise tightly.


c.
A292398C01
1.188,0.635 0.781,0.635 false 0.906,1.729 0.552,1.729 false 0.604,0.552 0.917,0.708 0.313,0.156 10 *1 0.385,1.646 0.698,1.802 0.313,0.156 10 *2
*1 SST (A)
*2 SST (B)


Confirm SST (A) and (B) shown in the illustration.

SST
09820-63021  


d.
A185232C01
2.063,0.698 1.708,0.313 1.708,0.313 1.552,0.313 true 2.344,2.156 2.771,2.448 2.771,2.448 2.99,1.063 true 1.354,0.24 1.552,0.563 0.198,0.323 10 false *1 2.719,2.469 3,2.708 0.281,0.24 10 false *2
*1 Rotor Shaft
*2 SST (A)


Place the rotor shaft end into SST (A).


e.
A185233C01
0.896,2.24 0.646,2.24 false 2.906,1.219 2.906,1.698 true 2.344,2.156 2.729,2.375 false 1.625,0.344 2.323,0.344 true 1.469,0.26 1.771,0.646 0.302,0.385 10 false *1 2.76,2.333 3,2.677 0.24,0.344 10 false *3 0.479,2.177 0.656,2.542 0.177,0.365 10 false *2 2.844,1.719 3.021,2.083 0.177,0.365 10 false *2
*1 Generator Pulley with Clutch
*2 SST (B)
*3 SST (A)


Fit SST (B) to the generator pulley with clutch.


f.
A194274
2.552,1.479 2.708,2.24 2.708,2.24 2.854,2.24 true 2.323,1.094 2.563,0.646 2.563,0.646 2.708,0.646 true 2.906,2.156 3.219,2.396 0.313,0.24 10 *2 2.781,0.583 3.094,0.771 0.313,0.188 10 *1
*1 SST (B)
*2 SST (A)


Loosen the pulley by turning SST (B) in the direction shown in the illustration.

NOTICE:
·

Check that the drive end frame is secured in the vise tightly.

·

Hold SST (A) tightly during the operation.




g.

Remove SST from the generator assembly.


h.

Remove the generator pulley with clutch from the rotor shaft.


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A293821

Remove the generator rotor assembly.


Hide 27310B 7.INSPECT GENERATOR DRIVE END FRAME BEARING

Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A128076

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A128077
0.187,0.662 0.485,0.808 0.299,0.146 10 SST 1.308,0.98 0.573,0.778 0.573,0.778 1.249,1.236 false

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)