Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Airbag sensor assembly branch line or connector

·

Power source circuit of airbag sensor assembly

·

Airbag sensor assembly ground circuit

·

Airbag sensor assembly



WIRING DIAGRAM

C240956E17
1.531,0.635 1.792,0.635 1.792,0.635 2.115,1.26 false 3.635,0.302 3.896,0.302 3.896,0.302 4.25,1.26 false 4.563,0.563 5.042,0.823 0.479,0.26 10 false DLC3 3.5,4.573 4.354,4.771 0.854,0.198 10 false Trouble Area 5.854,2.802 7.031,3.323 1.177,0.521 10 false Combination Meter Assembly 0.26,0.542 1.49,1.021 1.229,0.479 10 false CAN No. 2 Junction Connector 3.344,4.125 4.958,4.313 1.615,0.188 10 false Airbag Sensor Assembly 2.333,3.74 2.708,3.99 0.375,0.25 10 false A/B 3.573,3.271 4.073,3.448 0.5,0.177 10 false CANH 4.052,3.271 4.479,3.448 0.427,0.177 10 false CANL 3.375,3.563 3.656,3.75 0.281,0.188 10 false IG2 4.521,3.365 4.792,3.604 0.271,0.24 10 false E1 4.521,3.75 4.813,4.01 0.292,0.26 10 false E2 3.625,3.063 3.802,3.24 0.177,0.177 10 false 13 4.292,3.052 4.5,3.313 0.208,0.26 10 false 22 6.188,2.167 6.656,2.396 0.469,0.229 10 false 120 Ω 0.667,2.167 1.094,2.427 0.427,0.26 10 false 120 Ω 1.427,4.958 3.344,5.292 1.917,0.333 10 false : CAN Main Bus Line (CANH) 1.438,5.375 3.354,5.708 1.917,0.333 10 false : CAN Main Bus Line (CANL) 4.396,4.969 6.146,5.302 1.75,0.333 10 false : CAN Branch Line (CANH) 4.385,5.375 6.094,5.708 1.708,0.333 10 false : CAN Branch Line (CANL) 3.094,3.469 3.323,3.719 0.229,0.25 10 false 21 4.771,3.292 4.948,3.469 0.177,0.177 10 false 25 4.781,3.667 4.958,3.844 0.177,0.177 10 false 26 1.688,0.198 3.708,0.521 2.021,0.323 10 false CAN No. 1 Junction Connector 3.094,4.125 3.375,4.302 0.281,0.177 10 false I47 0.802,2.802 1.177,3.042 0.375,0.24 10 false ECM 0.083,0.125 1.458,0.438 1.375,0.313 12 false V Bus (for LHD): 5.594,2.802 5.927,3.042 0.333,0.24 10 false I18 0.479,2.802 0.833,3.031 0.354,0.229 10 false A25

C241452E12
4.604,1.26 4.844,0.927 4.844,0.927 5.01,0.927 false 2.615,1.26 3.135,0.656 3.135,0.656 3.271,0.656 false 2.146,0.563 2.625,0.823 0.479,0.26 10 false DLC3 3.5,4.583 4.469,4.896 0.969,0.313 10 false Trouble Area 0.385,2.813 1.563,3.354 1.177,0.542 10 false Combination Meter Assembly 3.375,0.563 5.417,0.875 2.042,0.313 10 false CAN No. 2 Junction Connector 3.354,4.115 5.021,4.344 1.667,0.229 10 false Airbag Sensor Assembly 2.323,3.729 2.698,3.979 0.375,0.25 10 false A/B 3.615,3.281 4.115,3.51 0.5,0.229 10 false CANH 4.073,3.292 4.542,3.521 0.469,0.229 10 false CANL 3.375,3.583 3.698,3.823 0.323,0.24 10 false IG2 4.521,3.375 4.74,3.583 0.219,0.208 10 false E1 4.521,3.76 4.823,3.99 0.302,0.229 10 false E2 3.615,3.052 3.917,3.271 0.302,0.219 10 false 13 4.281,3.052 4.531,3.281 0.25,0.229 10 false 22 6.146,2.188 6.594,2.469 0.448,0.281 10 false 120 Ω 0.667,2.198 1.146,2.49 0.479,0.292 10 false 120 Ω 1.406,4.958 3.323,5.292 1.917,0.333 10 false : CAN Main Bus Line (CANH) 1.417,5.365 3.333,5.698 1.917,0.333 10 false : CAN Main Bus Line (CANL) 4.385,4.969 6.135,5.302 1.75,0.333 10 false : CAN Branch Line (CANH) 4.385,5.375 6.094,5.708 1.708,0.333 10 false : CAN Branch Line (CANL) 3.104,3.49 3.344,3.698 0.24,0.208 10 false 21 4.771,3.292 4.99,3.51 0.219,0.219 10 false 25 4.781,3.667 4.99,3.948 0.208,0.281 10 false 26 5.125,0.854 7.104,1.208 1.979,0.354 10 false CAN No. 1 Junction Connector 3.083,4.115 3.438,4.354 0.354,0.24 10 false I47 6.271,2.792 6.688,3.052 0.417,0.26 10 false ECM 0.094,0.188 1.49,0.594 1.396,0.406 12 false V Bus (for RHD): 0.094,2.802 0.469,3.094 0.375,0.292 10 false I18 5.938,2.792 6.281,3 0.344,0.208 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure (w/o blind spot monitor system): Turn the ignition switch to ON, wait at least 10 seconds, and then drive the vehicle at a speed of 6 km/h (4 mph) or more for at least 6 seconds. Check that the warning light remains off after turning off following the initial light check.

·

DTC check procedure (w/ blind spot monitor system): Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 11.68 seconds, and then drive the vehicle at a speed of 6 km/h (4 mph) or more for at least 6 seconds. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIRBAG SENSOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the airbag sensor assembly connector.


c.
C188243C32
0.333,1.958 0.719,2.219 0.385,0.26 1.333,2.365 1.135,2.802 1.135,2.802 1.042,2.802 false 1.448,2.115 1.698,2.792 1.698,2.792 1.802,2.792 false 0.167,0.146 2.521,0.49 2.354,0.344 10 *a 1.865,2.719 2.323,2.875 0.458,0.156 10 CANH 0.688,2.729 1.146,2.885 0.458,0.156 10 CANL 0.427,2 0.74,2.156 0.313,0.156 10 I47
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-13 (CANH) - I47-22 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIRBAG SENSOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C188243C33
1.552,1.021 1.938,1.281 0.385,0.26 1.771,2.365 1.979,2.865 1.979,2.865 2.073,2.865 false 1.656,2.354 1.469,2.833 1.469,2.833 1.375,2.833 false 1.208,2.375 0.833,2.813 0.833,2.813 0.74,2.813 false 0.167,0.146 2.521,0.49 2.354,0.344 10 false *a 1.156,2.75 1.448,3 0.292,0.25 10 false E1 1.646,1.073 1.979,1.229 0.333,0.156 10 false I47 0.469,2.719 0.854,2.948 0.385,0.229 10 false IG2 2.167,2.771 2.531,3.021 0.365,0.25 10 false E2
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-25 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
I47-26 (E2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I47-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)