Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0208 Lost Communication with "Seat Control Module A" No communication from the position control ECU and switch assembly continues.
·

Position control ECU and switch assembly branch line or connector

·

Power source circuit of position control ECU and switch assembly

·

Position control ECU and switch assembly ground circuit

·

Position control ECU and switch assembly


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.

HINT:

This diagnosis procedure is for when DTC U0208 is output by the main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body).


WIRING DIAGRAM

C257124E02
1.792,0.75 1.917,0.219 1.917,0.219 2.125,0.219 false 4.76,0.75 4.76,0.271 4.76,0.271 5.01,0.271 false 0.698,1.656 1.094,1.802 0.396,0.146 10 false 120 Ω 0.042,2.302 0.323,2.448 0.281,0.146 10 false I12 6.146,1.656 6.542,1.802 0.396,0.146 10 false 120 Ω 0.281,2.302 1.427,2.917 1.146,0.615 10 false Main Body ECU (Multiplex Network Body ECU) 3.135,2.74 3.594,2.885 0.458,0.146 10 false CANP 2.583,3.646 4.604,4.01 2.021,0.365 10 false Position Control ECU and Switch Assembly (for Driver Side) 3.125,4.479 4.031,4.667 0.906,0.188 10 false Trouble Area 2.958,2.938 3.427,3.083 0.469,0.146 10 false +B 2.958,3.365 3.427,3.51 0.469,0.146 10 false SYSB 2.698,2.771 2.823,2.917 0.125,0.146 10 false 7 3.156,2.542 3.271,2.688 0.115,0.146 10 false 8 4.042,2.542 4.167,2.688 0.125,0.146 10 false 7 4.49,2.906 4.615,3.052 0.125,0.146 10 false 2 3.969,3.083 4.323,3.229 0.354,0.146 10 false GND 3.698,2.74 4.156,2.885 0.458,0.146 10 false CANN 1.417,4.99 3.354,5.167 1.938,0.177 10 false : CAN Main Bus Line (CANH) 1.417,5.396 3.354,5.573 1.938,0.177 10 false : CAN Main Bus Line (CANL) 4.417,4.99 6.146,5.167 1.729,0.177 10 false : CAN Branch Line (CANH) 4.417,5.396 6.115,5.573 1.698,0.177 10 false : CAN Branch Line (CANL) 5.604,2.281 6.823,2.635 1.219,0.354 10 false CAN No. 5 Junction Connector 2.177,0.146 4.313,0.333 2.135,0.188 10 false CAN No. 3 Junction Connector 1.688,3.063 2.469,3.24 0.781,0.177 10 false P/SEAT FR 1.688,3.51 2.542,3.688 0.854,0.177 10 false ECU-B NO. 1 2.656,3.188 2.833,3.365 0.177,0.177 10 false 12 3.323,2.542 3.625,2.688 0.302,0.146 10 false e12 3.719,2.542 4.031,2.688 0.313,0.146 10 false e12 4.417,3.073 4.688,3.219 0.271,0.146 10 false e11 2.625,2.938 2.885,3.083 0.26,0.146 10 false e11 2.625,3.365 2.885,3.51 0.26,0.146 10 false e12 0.125,0.052 1.833,0.448 1.708,0.396 12 false Sub bus 1 (for LHD): 5.031,0.198 7.031,0.458 2,0.26 10 false CAN No. 4 Junction Connector

C257125E02
1.917,0.75 2.24,0.417 2.24,0.417 2.448,0.417 false 0.677,1.656 1.073,1.802 0.396,0.146 10 false 120 Ω 0.25,2.302 0.531,2.448 0.281,0.146 10 false I12 6.125,1.656 6.521,1.802 0.396,0.146 10 false 120 Ω 0.479,2.302 1.635,2.906 1.156,0.604 10 false Main Body ECU (Multiplex Network Body ECU) 3.563,2.74 4.021,2.885 0.458,0.146 10 false CANP 3.156,3.708 5.219,4.177 2.063,0.469 10 false Position Control ECU and Switch Assembly (for Driver Side) 3.552,4.479 4.458,4.667 0.906,0.188 10 false Trouble Area 3.385,2.938 3.854,3.083 0.469,0.146 10 false +B 3.385,3.365 3.854,3.51 0.469,0.146 10 false SYSB 3.125,2.771 3.25,2.917 0.125,0.146 10 false 7 3.583,2.542 3.698,2.688 0.115,0.146 10 false 8 4.469,2.542 4.594,2.688 0.125,0.146 10 false 7 4.917,2.917 5.042,3.063 0.125,0.146 10 false 2 4.396,3.083 4.75,3.229 0.354,0.146 10 false GND 4.125,2.74 4.583,2.885 0.458,0.146 10 false CANN 1.396,4.99 3.333,5.167 1.938,0.177 10 false : CAN Main Bus Line (CANH) 1.396,5.396 3.333,5.573 1.938,0.177 10 false : CAN Main Bus Line (CANL) 4.396,4.99 6.125,5.167 1.729,0.177 10 false : CAN Branch Line (CANH) 4.396,5.396 6.094,5.573 1.698,0.177 10 false : CAN Branch Line (CANL) 5.583,2.281 6.823,2.656 1.24,0.375 10 false CAN No. 4 Junction Connector 2.5,0.344 4.635,0.531 2.135,0.188 10 false CAN No. 3 Junction Connector 2.115,3.063 2.896,3.24 0.781,0.177 10 false P/SEAT FR 2.115,3.51 2.969,3.688 0.854,0.177 10 false ECU-B NO. 1 3.083,3.188 3.26,3.365 0.177,0.177 10 false 12 3.75,2.542 4.052,2.688 0.302,0.146 10 false d12 4.135,2.542 4.448,2.688 0.313,0.146 10 false d12 4.844,3.073 5.115,3.219 0.271,0.146 10 false d11 3.042,2.938 3.302,3.083 0.26,0.146 10 false d11 3.042,3.365 3.302,3.51 0.26,0.146 10 false d12 0.104,0.052 1.854,0.448 1.75,0.396 12 false Sub Bus 1 (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 10 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
HINT:

If DTC U1002 is output from Main Body of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in the sub bus 1.



Result:
Result Proceed to
U1002 is not output from main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body) A
U1002 is output from main body ECU (multiplex network body ECU) (Intelligent tester display: Main Body) B



A

2.CHECK FOR OPEN IN SUB BUS 1 LINES (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 1 LINES (POSITION CONTROL ECU AND SWITCH ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the position control ECU and switch assembly connector.


c.
C188242C20
1.51,0.688 1.906,0.938 0.396,0.25 1.51,0.365 1.906,0.615 0.396,0.25 1.708,2.969 1.521,2.563 false 1.292,2.51 0.792,2.969 false 1.531,2.99 2.021,3.229 0.49,0.24 10 false CANP 0.51,3 0.979,3.198 0.469,0.198 10 false CANN 1.604,0.729 1.927,0.896 0.323,0.167 10 false d12 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 1.604,0.396 1.927,0.563 0.323,0.167 10 false e12 1.979,0.396 2.406,0.615 0.427,0.219 12 false *A 1.979,0.708 2.406,0.927 0.427,0.219 12 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: for LHD

*2: for RHD

e12-8 (CANP) - e12-7 (CANN)*1
d12-8 (CANP) - d12-7 (CANN)*2
Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the position control ECU and switch assembly connector.


b.
C278316C06
1.448,0.344 1.917,0.625 0.469,0.281 1.5,2.948 1.969,3.229 0.469,0.281 1.448,0.031 1.917,0.313 0.469,0.281 1.5,2.625 1.969,2.906 0.469,0.281 0.865,4.448 1.156,4.115 false 0.656,3.292 1.146,3.615 false 2.313,2.521 2.083,2.156 false 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.573,0.396 2.031,0.646 0.458,0.25 10 false d12 1.625,3 1.969,3.219 0.344,0.219 10 false d11 2.323,2.521 2.938,2.719 0.615,0.198 10 false SYSB 0.323,3.177 0.771,3.385 0.448,0.208 10 false GND 0.646,4.438 0.958,4.635 0.313,0.198 10 false +B 1.573,0.073 2.031,0.323 0.458,0.25 10 false e12 2,0.083 2.667,0.323 0.667,0.24 12 false *A 2.01,0.385 2.677,0.625 0.667,0.24 12 false *B 1.625,2.677 1.969,2.896 0.344,0.219 10 false e11 2.063,2.667 2.729,2.906 0.667,0.24 12 false *A 2.063,2.99 2.729,3.229 0.667,0.24 12 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: for LHD

*2: for RHD

e11-2 (GND) - Body ground*1
d11-2 (GND) - Body ground*2
Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: for LHD

*2: for RHD

e11-7 (+B) - Body ground*1
d11-7 (+B) - Body ground*2
Ignition switch off 11 to 14 V
e12-12 (SYSB) - Body ground*1
d12-12 (SYSB) - Body ground*2
Ignition switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE POSITION CONTROL ECU & SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)