Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074591 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front passenger door or the front door outside handle assembly (for front passenger door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [front passenger door electrical key antenna]), or there may be wave interference.

HINT:

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.


WIRING DIAGRAM

B281953E08
1.302,0.694 1.687,0.854 0.385,0.161 10 ANT1 1.287,1.165 1.686,1.326 0.399,0.161 10 ANT2 0.31,3.454 1.2,3.614 0.89,0.161 10 V1*1, W1*2 3.154,4.07 3.894,4.231 0.74,0.161 10 *1: for LHD 3.154,4.35 3.894,4.511 0.74,0.161 10 *2: for RHD 1.352,3.009 1.696,3.153 0.344,0.144 10 GND 1.77,1.053 1.876,1.211 0.106,0.159 10 3 1.779,2.91 1.884,3.064 0.106,0.154 10 2 1.772,0.602 1.878,0.747 0.106,0.146 10 6 5.745,0.722 6.162,0.889 0.417,0.167 10 CLG2 5.745,1.19 6.175,1.346 0.43,0.156 10 CG2B 5.745,3.031 5.924,3.195 0.178,0.164 10 E 5.436,0.512 5.666,0.67 0.231,0.158 10 11 5.436,0.722 5.666,0.879 0.231,0.158 10 I78 5.436,1.184 5.666,1.341 0.231,0.158 10 I78 5.436,1.645 5.666,1.803 0.231,0.158 10 I78 5.436,2.107 5.666,2.265 0.231,0.158 10 I78 5.436,2.569 5.666,2.727 0.231,0.158 10 I78 5.403,3.031 5.668,3.189 0.266,0.158 10 A43 5.418,0.987 5.636,1.153 0.218,0.166 10 10 1.554,1.618 1.689,1.779 0.134,0.161 10 B 1.287,2.088 1.686,2.248 0.399,0.161 10 SENS 1.77,1.977 1.876,2.136 0.106,0.159 10 4 1.772,1.526 1.878,1.672 0.106,0.146 10 5 5.745,1.648 6.162,1.815 0.417,0.167 10 POS2 5.745,2.116 6.175,2.272 0.43,0.156 10 SEN2 5.428,1.436 5.606,1.594 0.178,0.158 10 21 5.428,1.911 5.62,2.077 0.192,0.166 10 23 1.287,2.564 1.686,2.725 0.399,0.161 10 TRG+ 1.77,2.44 1.876,2.598 0.106,0.159 10 1 5.745,2.573 6.175,2.73 0.43,0.156 10 TSW2 5.47,2.374 5.662,2.54 0.192,0.166 10 8 5.424,2.83 5.619,2.992 0.195,0.162 10 11 5.381,3.573 7.005,3.94 1.624,0.367 10 Certification ECU (Smart Key ECU Assembly) 0.312,3.62 2.103,4.198 1.792,0.578 10 Front Door Outside Handle Assembly (for Front Passenger Door)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the engine switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.CHECK WAVE ENVIRONMENT

NG

2.CHECK WAVE ENVIRONMENT
a.
B281966E03
1.229,1.229 1.438,1.417 0.208,0.188 10 false *a 2.365,3.51 2.573,3.698 0.208,0.188 10 false *a 0.094,0.021 0.667,0.177 0.573,0.156 10 false *A 0.104,2.104 0.677,2.26 0.573,0.156 10 false *B

Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for front passenger door) and perform an entry function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result:
Result Proceed to
Entry function does not operate normally. A
Entry function operates normally. B



A

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)

B

AFFECTED BY WAVE INTERFERENCE

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the V1*1, or W1*2 front door outside handle assembly (for front passenger door) connector.


b.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

·

*1: for LHD

·

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
V1-3 (ANT2) - I78-10 (CG2B) Always Below 1 Ω
V1-6 (ANT1) - I78-11 (CLG2) Always Below 1 Ω
V1-5 (B) - I78-21 (POS2) Always Below 1 Ω
V1-2 (GND) - Body ground Always Below 1 Ω
V1-3 (ANT2) or I78-10 (CG2B) - Body ground Always 10 kΩ or higher
V1-6 (ANT1) or I78-11 (CLG2) - Body ground Always 10 kΩ or higher
V1-5 (B) or I78-21 (POS2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
W1-3 (ANT2) - I78-10 (CG2B) Always Below 1 Ω
W1-6 (ANT1) - I78-11 (CLG2) Always Below 1 Ω
W1-5 (B) - I78-21 (POS2) Always Below 1 Ω
W1-2 (GND) - Body ground Always Below 1 Ω
W1-3 (ANT2) or I78-10 (CG2B) - Body ground Always 10 kΩ or higher
W1-6 (ANT1) or I78-11 (CLG2) - Body ground Always 10 kΩ or higher
W1-5 (B) or I78-21 (POS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)
a.
B250975C32
0.313,0.396 0.833,0.698 0.521,0.302 0.313,0.781 0.833,1.083 0.521,0.302 2.448,0.188 2.208,0.188 2.208,0.188 1.813,0.729 false 2.448,1.375 2.208,1.375 2.208,1.375 1.833,0.938 false 1.719,0.729 1.719,0.167 1.719,0.167 1.281,0.167 false 1.719,0.938 1.719,1.5 1.719,1.5 1.281,1.5 false 0.063,0.01 0.323,0.26 0.26,0.25 10 false *a 0.063,1.531 0.323,1.781 0.26,0.25 10 false *1 0.135,2.479 0.469,2.677 0.333,0.198 10 false GND 2.469,1.313 2.865,1.51 0.396,0.198 10 false ANT1 0.458,0.469 0.688,0.635 0.229,0.167 10 false V1 2.479,0.115 2.875,0.313 0.396,0.198 10 false ANT2 0.438,0.844 0.896,1.146 0.458,0.302 10 false W1 0.885,0.469 1.063,0.635 0.177,0.167 10 false *A 0.885,0.844 1.063,1.01 0.177,0.167 10 false *B 0.948,0.094 1.344,0.292 0.396,0.198 10 false GND 1.146,1.427 1.323,1.625 0.177,0.198 10 false B
*A for LHD
*B for RHD
*1 Waveform
*a Front view of wire harness connector
(to Front Door Outside handle assembly (for front passenger door))


Disconnect the V1*1 or W1*2 front door outside handle assembly (for front passenger door) connector.


b.

Connect the I78 certification ECU (smart key ECU assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V1-5 (B) - V1-2 (GND)*1
W1-5 (B) - W1-2 (GND)*2
Engine switch off → on (IG) 9 to 14 V → Below 2 V



d.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
V1-3 (ANT2) - V1-6 (ANT1)*1
W1-3 (ANT2) - W1-6 (ANT1)*2
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)


·

*1: for LHD

·

*2: for RHD



Result:
Proceed to
OK
NG



OK

5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)
a.

Temporarily replace the front door outside handle assembly (for front passenger door) with a new or known good one.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
a.

Check that the entry functions operate normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry functions operate normally.



Result:
Proceed to
OK
NG



OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)