Use the same procedure for both the RH and LH sides.
The procedure described below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
69284C
3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.
67492A
4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Disengage the 3 clips and remove the front door lower frame bracket garnish.
5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.
6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.
74220
7.REMOVE FRONT ARMREST ASSEMBLY
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.
81230
8.REMOVE COURTESY LIGHT ASSEMBLY
67602
9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
| *1 | Protective Tape |
Put protective tape around the front door panel.
Remove the 3 screws.
Using a clip remover, disengage the 10 clips.
| *1 | Reference Boss |
| *2 | Front Door Inner Glass Weatherstrip |
Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
Disengage the reference boss from the front door panel.
Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.
Disconnect the connector.
Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.
69206B
10.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly.
68172A
11.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
| *1 | Screwdriver |
Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
84927
12.REMOVE SEAT MEMORY SWITCH (w/ Memory)
86160
13.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
14.REMOVE MIRROR SUB-ASSEMBLY WITH COVER
89430
15.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)
67832
16.REMOVE FRONT DOOR SERVICE HOLE COVER
Disconnect each connector.
Disengage the 3 clamps.
Remove the front door service hole cover.
Remove any remaining butyl tape from the door.
68102
17.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the grommet.
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Disconnect the power window regulator master switch assembly.
Remove the 2 bolts.
After the bolts are removed, do not allow the door glass to fall.
Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
Do not damage the door glass.
18.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
| *1 | Temporary Bolt |
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.
Remove the 5 bolts.
Remove the front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
85720D
19.REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.
67924
20.REMOVE NO. 2 FRONT DOOR STIFFENER CUSHION
| *1 | Double-sided Tape |
Remove the 2 bolts.
Disengage the 2 guides and remove the No. 2 front door stiffener cushion.
68151C
21.REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
67402F
22.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Remove the 2 bolts.
Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.
67404F
23.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Remove the 2 bolts.
Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.
24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
69217F
25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.
69217F
26.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
69220
27.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
w/ Smart Entry and Start System:
Disengage the 2 claws.
Using a screwdriver, disconnect the connector.
Remove the front door outside handle assembly as shown in the illustration.
69241H
28.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD
Disengage the 3 claws and remove the front door front outside handle pad.
69242E
29.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD
Disengage the 2 claws and remove the front door rear outside handle pad.
69040A
30.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
| *1 | Front Door Lock Open Rod |
Using a T30 "TORX" socket wrench, remove the 3 screws.
Slide the front door lock with motor assembly downward, and remove the front door lock with motor assembly and cables as a unit.
When reusing the front door lock with motor assembly:
Remove the door lock wiring harness seal from the front door lock with motor assembly.
69720B
31.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
Remove the front door lock remote control cable assembly.
69760C
32.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY
Using a screwdriver, disengage the 3 claws.
Remove the front door inside locking cable assembly.
69202A
33.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
w/ Smart Entry and Start System:
Disconnect the connector.
Disengage the 3 clamps.
| *1 | Door Handle Nut |
| *a | Outside |
| *b | Inside |
Using a T30 "TORX" socket wrench, remove the screw and door handle nut.
Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it.
82186B
34.REMOVE FRONT DOOR WIRE (w/ Smart Entry and Start System)
Disengage the 3 clamps and remove the front door wire.
69312
35.REMOVE FRONT DOOR LOCK OPEN ROD
Remove the front door lock open rod as indicated by the arrows and in the order shown in the illustration.
68620
36.REMOVE FRONT DOOR CHECK ASSEMBLY
Remove the 3 bolts and front door check assembly.
67862
37.REMOVE FRONT DOOR WEATHERSTRIP
Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.
67664C
38.REMOVE DOOR FRAME GARNISH
Disengage the clip and remove the door frame garnish.
This garnish needs to be replaced with a new one because the clip will break when removing it.
67864B
39.REMOVE FRONT DOOR NO. 2 WEATHERSTRIP
Using a clip remover, disengage the 8 clips and remove the front door No. 2 weatherstrip.
67001A
40.REMOVE FRONT DOOR PANEL CUSHION
Disengage the 2 claws and remove the 2 front door panel cushions.
67481C
41.REMOVE FRONT DOOR FRONT LOWER FRAME SEAL
Remove the front door front lower frame seal.
75720
42.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY
75756C
43.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING
75754A
44.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
75986B
45.REMOVE FRONT DOOR STRIPE
75976G
46.REMOVE FRONT DOOR LOWER OUTSIDE STRIPE