Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074591 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A1  Open in Driver Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for driver door) [electrical key antenna] at intervals of 0.25 seconds. For the front door outside handle assembly (for driver door) [electrical key antenna] to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 0.25 seconds. DTC B27A1 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [electrical key antenna] (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A1 Open in Driver Side Electrical Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Wire harness or connector

·

Front door outside handle assembly (for driver door)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for driver door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A1 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B281953E05
1.29,0.734 1.675,0.894 0.385,0.161 10 ANT1 1.276,1.177 1.675,1.338 0.399,0.161 10 ANT2 0.243,3.452 0.625,3.612 0.382,0.161 10 W1*1 2.989,4.103 3.701,4.264 0.712,0.161 10 *1: for LHD 2.989,4.383 3.732,4.544 0.743,0.161 10 *2: for RHD 0.691,3.452 1.045,3.612 0.354,0.161 10 V1*2 1.327,3.021 1.671,3.165 0.344,0.144 10 GND 1.773,1.093 1.878,1.251 0.106,0.159 10 3 1.781,2.95 1.887,3.104 0.106,0.154 10 2 1.775,0.642 1.88,0.787 0.106,0.146 10 6 5.748,0.72 6.165,0.887 0.417,0.167 10 CLG1 5.748,1.188 6.178,1.344 0.43,0.156 10 CG1B 5.748,3.028 5.878,3.193 0.13,0.164 10 E 5.436,0.524 5.649,0.682 0.213,0.158 10 12 5.436,0.72 5.649,0.877 0.213,0.158 10 I78 5.436,1.182 5.649,1.34 0.213,0.158 10 I78 5.436,1.644 5.649,1.802 0.213,0.158 10 I78 5.436,2.107 5.649,2.265 0.213,0.158 10 I78 5.436,2.569 5.649,2.727 0.213,0.158 10 I78 5.399,3.032 5.664,3.189 0.265,0.158 10 A43 5.435,0.999 5.653,1.165 0.218,0.166 10 13 1.529,1.644 1.663,1.805 0.134,0.161 10 B 1.276,2.1 1.675,2.26 0.399,0.161 10 SENS 1.773,2.017 1.878,2.176 0.106,0.159 10 4 1.775,1.566 1.88,1.712 0.106,0.146 10 5 5.748,1.645 6.165,1.813 0.417,0.167 10 POS1 5.748,2.114 6.178,2.27 0.43,0.156 10 SEN1 5.444,1.448 5.623,1.606 0.178,0.158 10 19 5.444,1.923 5.636,2.089 0.192,0.166 10 22 1.276,2.562 1.675,2.723 0.399,0.161 10 TRG+ 1.773,2.48 1.878,2.638 0.106,0.159 10 1 5.748,2.571 6.178,2.727 0.43,0.156 10 TSW1 5.444,2.386 5.636,2.552 0.192,0.166 10 20 5.441,2.842 5.636,3.004 0.195,0.162 10 11 5.369,3.585 6.994,3.952 1.624,0.367 10 Certification ECU (Smart Key ECU Assembly) 0.244,3.618 2.142,3.993 1.898,0.376 10 Front Door Outside Handle Assembly (for Driver Door)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the engine switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The front door outside handle assembly (for driver door) has an antenna coil between ANT1 and ANT2 terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)
a.

Disconnect the I78 and A43 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I78-12 (CLG1) - W1-6 (ANT1) Always Below 1 Ω
I78-13 (CG1B) - W1-3 (ANT2) Always Below 1 Ω
A43-11 (E) - Body ground Always Below 1 Ω
W1-2 (GND) - Body ground Always Below 1 Ω
I78-12 (CLG1) or W1-6 (ANT1) - Body ground Always 10 kΩ or higher
I78-13 (CG1B) or W1-3 (ANT2) - Body ground Always 10 kΩ or higher


for RHD
Tester Connection Condition Specified Condition
I78-12 (CLG1) - V1-6 (ANT1) Always Below 1 Ω
I78-13 (CG1B) - V1-3 (ANT2) Always Below 1 Ω
A43-11 (E) - Body ground Always Below 1 Ω
V1-2 (GND) - Body ground Always Below 1 Ω
I78-12 (CLG1) or V1-6 (ANT1) - Body ground Always 10 kΩ or higher
I78-13 (CG1B) or V1-3 (ANT2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA)
a.

Connect the I78 and A43 certification ECU (smart key ECU assembly) connectors.

B271427C19
2.125,0.594 2.5,0.823 0.375,0.229 4.75,0.594 5.125,0.823 0.375,0.229 4.823,1.417 4.604,1.979 false 2.708,1.531 2.531,1.979 false 5,1.427 5.219,1.99 false 0.198,0.146 0.417,0.344 0.219,0.198 10 *a 1.208,2.823 1.427,3.021 0.219,0.198 10 *1 0.969,3.635 1.333,3.802 0.365,0.167 10 GND 3.854,3.635 4.219,3.802 0.365,0.167 10 GND 4.146,2.823 4.365,3.021 0.219,0.198 10 *2 2.479,2 2.74,2.271 0.26,0.271 10 E 4.417,2 4.979,2.323 0.563,0.323 10 CG1B 5.125,2.021 5.625,2.271 0.5,0.25 10 CLG1 2.188,0.635 2.677,0.979 0.49,0.344 10 A43 4.854,0.635 5.219,0.938 0.365,0.302 10 I78
*1 Waveform 1 *2 Waveform 2
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
- -



b.

Connect the W1*3 or V1*4 front door outside handle assembly (for driver door) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
I78-12 (CLG1) - A43-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)
I78-12 (CLG1) - A43-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)
I78-13 (CG1B) - A43-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)


*1: For details about the areas that are inside the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

*3: for LHD

*4: for RHD



Result:
Proceed to
OK
NG



OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)
a.

Temporarily replace the front door outside handle assembly (for driver door) with a new or known good one.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A1 is not output.



Result:
Proceed to
OK
NG



OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)