Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074592 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2284  Brake Signal Malfunction  


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2284 Brake Signal Malfunction Brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection logic*) do not match.
·

ECU-B NO.1 fuse

·

STOP fuse

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation

Connect the cable to the negative (-) battery terminal, release the brake pedal and wait 20 seconds or more. Then depress the brake pedal for 20 seconds or more.



*: Only detected while a malfunction is present and the engine switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start (the indicator in the combination meter is not illuminated in green). However, the engine can be started by turning the engine switch on (ACC) and then pressing and holding it.
·

If there is a malfunction when the direct line is on, the engine can be started by pressing the engine switch with the brake pedal released.

·

If there is a malfunction when the direct line is off, the engine cannot be started by pressing the engine switch with the brake pedal depressed.


-

WIRING DIAGRAM

B284660
0.167,0.813 1.24,1.125 1.073,0.313 10 false from Battery 0.188,1.563 1.26,1.865 1.073,0.302 10 false from Battery 2.344,1.917 3.49,2.302 1.146,0.385 10 false Stop Light Switch Assembly 3.979,3.021 5.552,3.438 1.573,0.417 10 false Certification ECU (Smart Key ECU Assembly) 1.729,1.719 2.26,1.969 0.531,0.25 10 false STOP 2.115,0.948 3.073,1.115 0.958,0.167 10 false ECU-B NO. 1 4.229,0.802 4.781,1.104 0.552,0.302 10 false CUTB 5.042,1.531 5.771,2.156 0.729,0.625 10 false CAN Communication Line 6.094,2.135 6.563,2.417 0.469,0.281 10 false ECM 4.229,1.573 4.802,1.885 0.573,0.313 10 false STP1 4.24,2.438 4.479,2.698 0.24,0.26 10 false E 2.344,1.771 2.708,2.042 0.365,0.271 10 false A33 3.979,0.688 4.26,1 0.281,0.313 10 false 10 3.979,1.458 4.281,1.729 0.302,0.271 10 false 18 3.969,2.313 4.24,2.531 0.271,0.219 10 false 11 3.635,3.021 4.01,3.281 0.375,0.26 10 false A43 3.281,1.458 3.479,1.625 0.198,0.167 10 false 1 2.521,1.458 2.781,1.698 0.26,0.24 10 false 2

CAUTION / NOTICE / HINT

HINT:

Check the connector connection to the terminal to make sure that there is no abnormality such as a loose connection, deformation, etc.


NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2284
Power Source Control
·

Stop Light Switch1


ABS/VSC/TRAC
·

Stop Light SW


-


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 Stop light switch1 ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.



Result:
Proceed to
OK
NG



OK

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A33 connector from the stop light switch assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-18 (STP1) - A33-1 Always Below 1 Ω
A43-18 (STP1) or A33-1 - Body ground Always 10 kΩ or higher



c.
B269097
0.344,1.979 0.802,2.26 0.458,0.281 1.354,2.313 0.979,2.823 false 0.073,0 0.406,0.24 0.333,0.24 10 *a 0.458,2.052 0.792,2.292 0.333,0.24 10 A43 0.802,2.844 1.229,3.083 0.427,0.24 10 STP1
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Reconnect the A33 stop light switch assembly connector.


d.

Disconnect the A43 certification ECU (smart key ECU assembly).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-18 (STP1) - Body ground Brake pedal released 1 V or less
Brake pedal depressed 9 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR