Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074592 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (ACC)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B285916E08
0.021,0.823 0.823,1.208 0.802,0.385 10 false from Battery 1.104,0.969 1.563,1.219 0.458,0.25 10 false AM2 2,0.615 2.229,0.875 0.229,0.26 10 false 2 3.323,1.031 3.448,1.271 0.125,0.24 10 false 4 2.281,0.813 2.667,1.115 0.385,0.302 10 false +B 2.76,1.208 3.281,1.406 0.521,0.198 10 false ACCD 4.823,1.51 5.698,1.781 0.875,0.271 10 false ACC NO. 1 4.833,2.74 5.76,3.042 0.927,0.302 10 false ACC NO. 2 1.958,2.875 3.521,3.323 1.563,0.448 10 false Certification ECU (Smart Key ECU Assembly) 3.719,2.979 6.479,3.302 2.76,0.323 10 false Instrument Panel Junction Block Assembly 2.281,1.615 2.531,1.844 0.25,0.229 10 false E 1.958,1.417 2.177,1.594 0.219,0.177 10 false 11 1.927,0.813 2.271,0.979 0.344,0.167 10 false A43 1.927,1.604 2.323,1.823 0.396,0.219 10 false A43 3.26,1.208 3.604,1.375 0.344,0.167 10 false I78 3.781,1.198 4.229,1.531 0.448,0.333 10 false 3B 3.792,1.042 4.031,1.208 0.24,0.167 10 false 23 3.792,0.604 4.031,0.771 0.24,0.167 10 false 3F 3.823,0.427 4.115,0.708 0.292,0.281 10 false 1 5.719,0.948 6.531,1.156 0.813,0.208 10 false ECU-ACC 5.927,2.083 6.333,2.604 0.406,0.521 10 false SFT LOCK-ACC 6.396,0.625 6.635,0.792 0.24,0.167 10 false 37 6.396,0.792 6.688,1.021 0.292,0.229 10 false 3B 6.396,1.802 6.688,2 0.292,0.198 10 false 32 6.438,2.302 6.677,2.469 0.24,0.167 10 false 7 6.385,1.969 6.677,2.177 0.292,0.208 10 false 3A 6.396,2.479 6.698,2.708 0.302,0.229 10 false 3B 0.188,3.052 1.01,3.219 0.823,0.167 10 false *1: for LHD 0.188,3.323 1.01,3.49 0.823,0.167 10 false *2: for RHD 3.792,0.781 4.031,0.948 0.24,0.167 10 false 3E 4.052,0.917 4.292,1.083 0.24,0.167 10 false *1 4.052,0.677 4.292,0.844 0.24,0.167 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (ACC) but does change to on (IG)
Power Source Control
·

Power Supply Condition

·

ACC Relay Monitor


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)