Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074601 ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short The transponder key amplifier coil built into the engine switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Terminal AGND, VC5, TXCT or CODE is open (includes disconnection of the engine switch).

·

The transponder key amplifier coil built into the engine switch is open.


·

Engine switch

·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)


DTC output confirmation operation:

With the shift lever in P, the key held near the engine switch and an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P -

Related Data List and Active Test
DTC Code Data List and Active Test
B2784 -

WIRING DIAGRAM

B271004
1.979,2.177 2.177,2.406 0.198,0.229 10 false 6 0.885,2.99 1.99,3.292 1.104,0.302 10 false Engine Switch 0.885,2.823 1.271,2.99 0.385,0.167 10 false I58 1.563,0.75 1.875,1 0.313,0.25 10 false VC5 1.448,2.302 1.906,2.677 0.458,0.375 10 false AGND 1.938,0.635 2.25,0.875 0.313,0.24 10 false 10 1.979,1.156 2.188,1.354 0.208,0.198 10 false 7 5.01,2.854 6.542,3.323 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly) 5.01,2.708 5.438,2.896 0.427,0.188 10 false I78 1.448,1.781 1.99,2.031 0.542,0.25 10 false CODE 1.5,1.24 1.958,1.396 0.458,0.156 10 false TXCT 1.979,1.677 2.177,1.875 0.198,0.198 10 false 8 5.104,0.635 5.313,0.844 0.208,0.208 10 false 1 5.052,2.177 5.385,2.396 0.333,0.219 10 false 24 5.104,1.146 5.49,1.438 0.385,0.292 10 false 9 5.104,1.656 5.313,1.927 0.208,0.271 10 false 7 5.313,0.76 5.625,1.01 0.313,0.25 10 false VC5 5.313,2.302 5.771,2.677 0.458,0.375 10 false AGND 5.313,1.792 5.885,2.094 0.573,0.302 10 false CODE 5.313,1.271 5.771,1.427 0.458,0.156 10 false TXCT

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I58 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-7 (CODE) - I58-8 (CODE) Always Below 1 Ω
I78-9 (TXCT) - I58-7 (TXCT) Always Below 1 Ω
I78-1 (VC5) - I58-10 (VC5) Always Below 1 Ω
I78-24 (AGND) - I58-6 (AGND) Always Below 1 Ω
I58-8 (CODE) - Body ground Always 10 kΩ or higher
I58-7 (TXCT) - Body ground Always 10 kΩ or higher
I58-10 (VC5) - Body ground Always 10 kΩ or higher
I58-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE ENGINE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE ENGINE SWITCH
a.

Temporarily replace the engine switch with a new or known good one.

Click hereEngine / Hybrid System>2GR-FE STARTING>ENGINE SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Proceed to
OK
NG



OK

END (ENGINE SWITCH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)