Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2012.02–2015.04
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074602 ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communication with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2799 Engine Immobiliser System Malfunction One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication with transponder key ECU assembly.


·

Wire harness or connector

·

ECM

·

Transponder key ECU assembly



WIRING DIAGRAM

B255097E28
0.938,1.99 1.323,2.198 0.385,0.208 10 false A25 0.938,2.125 1.479,2.354 0.542,0.229 10 false ECM 5.396,1.885 5.75,2.125 0.354,0.24 10 false I19 5.396,2.042 6.823,2.51 1.427,0.469 10 false Transponder Key ECU Assembly 1.281,1.271 1.635,1.552 0.354,0.281 10 false IMI 1.24,0.521 1.719,0.813 0.479,0.292 10 false IMO 5.708,0.521 6,0.677 0.292,0.156 10 false EFII 5.708,1.271 6.073,1.427 0.365,0.156 10 false EFIO 5.469,1.135 5.646,1.281 0.177,0.146 10 false 13 5.469,0.375 5.646,0.531 0.177,0.156 10 false 12 1.615,0.375 1.927,0.646 0.313,0.271 10 false 30 1.635,1.135 1.938,1.5 0.302,0.365 10 false 31

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


HINT:

If the transponder key ECU assembly DTC is output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.RE-REGISTER ECU COMMUNICATION ID
2.RE-REGISTER ECU COMMUNICATION ID
a.

Re-register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID WAS NOT REGISTERED CORRECTLY)

NG

4.CHECK CONNECTION OF CONNECTOR
4.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)

NG

CONNECT CONNECTORS PROPERLY

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the transponder key ECU assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-12 (EFII) - A25-30 (IMO) Always Below 1 Ω
I19-13 (EFIO) - A25-31 (IMI) Always Below 1 Ω
I19-12 (EFII) - Body ground Always 10 kΩ or higher
I19-13 (EFIO) - Body ground Always 10 kΩ or higher
A25-30 (IMO) - Body ground Always 10 kΩ or higher
A25-31 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
8.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY