Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2012.02–2015.04
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074602 ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
B279A Theft Deterrent System Communication Line High Fixation Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Wire harness or connector

·

ECM

·

Transponder key ECU assembly



WIRING DIAGRAM

B203372E67
0.729,2.135 1.49,2.427 0.76,0.292 10 false ECM 0.729,1.969 1.104,2.167 0.375,0.198 10 false A25 5.729,1.25 6.083,1.438 0.354,0.188 10 false GND 1.302,0.5 1.708,0.813 0.406,0.313 10 false IMI 1.594,0.385 1.99,0.813 0.396,0.427 10 false 31 5.479,1.125 5.781,1.521 0.302,0.396 10 false 16 5.583,2.094 6.719,2.49 1.135,0.396 10 false Transponder Key ECU Assembly 5.594,1.948 6.115,2.385 0.521,0.438 10 false I19 5.729,0.5 6.073,0.646 0.344,0.146 10 false EFIO 5.479,0.385 5.781,0.646 0.302,0.26 10 false 13

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

If any DTCs other than DTC B279A are output, troubleshoot those DTCs first.


Result:
Result Proceed to
DTC B279A is output A
DTC B279A and other DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)

B

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the transponder key ECU assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-13 (EFIO) - A25-31 (IMI) Always Below 1 Ω
I19-13 (EFIO) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
I19-13 (EFIO) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)
a.

Reconnect the transponder key ECU assembly connector.


b.

Reconnect the ECM connector.


c.

Using an oscilloscope, check the waveform.

B278949C01
3.344,0.135 3.635,0.333 0.292,0.198 3.167,0.979 3.167,1.313 3.167,1.313 3.031,1.313 false 3.375,0.979 3.375,1.531 3.375,1.531 3.031,1.531 false 2.146,0.052 2.323,0.354 0.177,0.302 10 *a 2.708,1.229 3.104,1.406 0.396,0.177 10 GND 2.698,1.458 3.052,1.635 0.354,0.177 10 EFIO 1.021,2.979 1.167,3.156 0.146,0.177 10 *b 3.156,3.125 3.302,3.302 0.146,0.177 10 *c 5.927,2.896 6.073,3.073 0.146,0.177 10 *e 5.927,2.177 6.073,2.354 0.146,0.177 10 *d 3.396,0.156 3.635,0.365 0.24,0.208 10 I19
*a Component with harness connected
(Transponder Key ECU Assembly)
*b GND
*c Waveform *d High
*e Low - -


Waveform (Reference):
Item Content
Terminal No. (Symbol) I19-13 (EFIO) - I19-16 (GND)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned ON after battery cable disconnected and reconnected.


OK:

Waveform is output normally (see illustration).



Result:
Proceed to
OK
NG



OK

NG

4.REPLACE TRANSPONDER KEY ECU ASSEMBLY
4.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.REGISTER KEY
5.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.REGISTER ECU COMMUNICATION ID
6.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC B279A is not output.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG