Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM2030EQ _58 Vehicle Interior _014669 SUPPLEMENTAL RESTRAINT SYSTEMS _0074625 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 62180A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Temporarily install the curtain shield airbag assembly with the 2 hooks.

B278811N02
2.938,2.396 3.073,2.604 0.135,0.208 10 false 1 2.563,2.406 2.75,2.625 0.188,0.219 10 false 2

NOTICE:
·

When installing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.

·

Do not twist the curtain shield airbag assembly when installing it.




d.

Install 2 new bolts in the order shown in the illustration.

Torque:
11 N*m (110 kgf*cm, 8 ft.*lbf)


e.

Install the curtain shield airbag assembly to the body panel with 5 claws, 6 new clips and 2 new spacers in the order shown in the illustration.

B278809C02
5.917,1.896 5.75,1.729 5.75,1.729 5.698,1.729 false 6.125,2.104 6.521,2.104 false 6.188,2.188 6.25,2.406 6.25,2.406 6.333,2.406 false 6.083,2.24 6.083,2.333 false 5.75,2.25 5.75,2.323 false 3.583,0.594 3.833,0.802 0.25,0.208 10 false 1 4,1.635 4.208,1.833 0.208,0.198 10 false 2 5.042,0.677 5.24,0.885 0.198,0.208 10 false 3 5.104,1.896 5.313,2.115 0.208,0.219 10 false 4 6.042,1 6.219,1.198 0.177,0.198 10 false 5 6.667,1.302 6.885,1.521 0.219,0.219 10 false 6 2.594,1.615 2.823,1.875 0.229,0.26 10 false 7 1.833,2.042 2.052,2.271 0.219,0.229 10 false 8 1.031,2.198 1.313,2.448 0.281,0.25 10 false 10 1.417,0.823 1.656,1.031 0.24,0.208 10 false 9 0.375,1.094 0.594,1.323 0.219,0.229 10 false 11 5.542,1.646 5.771,1.844 0.229,0.198 10 false *1 6.542,2.021 6.719,2.177 0.177,0.156 10 false *2 5.656,2.313 5.885,2.521 0.229,0.208 10 false *4 6.323,2.313 6.542,2.5 0.219,0.188 10 false *3 6.01,2.323 6.24,2.51 0.229,0.188 10 false *5
*1 Pin *2 Clip
*3 Curtain Shield Airbag Assembly *4 Body Panel
*5 Spacer - -



f.
B278807

Push in a new pin to each clip.

NOTICE:

Make sure that the pins of the clips are pushed in firmly.



g.
B278805C02
1.906,1.958 2.198,2.198 false 1.76,0.917 1.469,0.917 1.469,0.917 1.333,0.781 false 2.24,2.156 2.5,2.365 0.26,0.208 10 false *1 1.802,0.833 2.073,1.083 0.271,0.25 10 false *2
*1 Airbag Connector
*2 Airbag Connector Lock


Connect the curtain shield airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



h.

Push in the lock to install the curtain shield airbag connector.


Hide 2.INSTALL ROOF HEADLINING ASSEMBLY