1.INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
| *1 | Clip (Black) |
| *2 | Clip (White) |
Install the 2 clips to the roof headlining assembly.
Put the roof headlining assembly into the vehicle through the front door RH.
Do not damage the roof headlining assembly or body interior.
Engage the 2 clips.
| *A | w/ Digital Audio Broadcasting Antenna | - | - |
Install the roof headlining assembly with the 2 clips.
Engage the 4 clamps to the front pillar LH.
Engage the 3 clamps to the front pillar RH.
Connect the bracket with the bolt to the front pillar RH.
Engage the 2 clamps and connect the connector to the rear pillar RH.
w/ Digital Audio Broadcasting Antenna:
Engage the clamp and connect the connector to the rear pillar LH.
w/ Rain Sensor:
Connect the connector to the rain sensor.
w/ EC Mirror:
Connect the connector to the inner rear view mirror.
2.INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
| *1 | Clip (Black) |
| *2 | Clip (White) |
Install the 2 clips to the roof headlining assembly.
Put the roof headlining assembly into the vehicle through the front door RH.
Do not damage the roof headlining assembly or body interior.
Engage the 2 clips and 2 fasteners.
| *A | w/ Digital Audio Broadcasting Antenna | - | - |
Install the roof headlining assembly with the 2 clips.
Engage the 4 clamps to the front pillar LH.
Engage the 3 clamps to the front pillar RH.
Connect the bracket with the bolt to the front pillar RH.
Engage the 2 clamps and connect the connector to the rear pillar RH.
Connect the connector to the sliding roof drive gear assembly.
w/ Digital Audio Broadcasting Antenna:
Engage the clamp and connect the connector to the rear pillar LH.
w/ Rain Sensor:
Connect the connector to the rain sensor.
w/ EC Mirror:
Connect the connector to the inner rear view mirror.
74348
3.INSTALL VISOR HOLDER
Engage the 2 claws.
Push in the visor holder as shown in the illustration.
Use the same procedure for the other visor holder.
74320
4.INSTALL VISOR ASSEMBLY LH
Install the visor assembly LH with the 2 screws.
74325
5.INSTALL VISOR BRACKET COVER (for LH Side)
Engage the 4 claws to install the visor bracket cover.
74310
6.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74325
7.INSTALL VISOR BRACKET COVER (for RH Side)
Use the same procedure as for the LH side.
63318C
8.INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
| *1 | Notch |
| *2 | Alignment Mark |
Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.
After installation, check that the corners fit correctly.
74610A
9.INSTALL ASSIST GRIP SUB-ASSEMBLY (for LH Side)
Put an assist grip sub-assembly together as shown in the illustration.
Engage the 2 clips to install the assist grip sub-assembly.
Engage the 4 claws to install the 2 assist grip covers
74610A
10.INSTALL ASSIST GRIP SUB-ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
74630E
11.INSTALL REAR ASSIST GRIP ASSEMBLY LH
Put an rear assist grip assembly LH together as shown in the illustration.
Engage the 2 clips to install the rear assist grip assembly LH.
Engage the 4 claws to install the 2 assist grip covers
74620C
12.INSTALL REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure as for the LH side.
81240
13.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)
81360T
14.INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)
63650A
15.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)
63650A
16.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)
89943
17.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
87834
18.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
19.INSTALL INSTRUMENT PANEL SAFETY PAD
20.INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSTALLATION
21.INSTALL FRONT SEAT ASSEMBLY RH
Use the same procedure as for the LH side.
62472A
22.INSTALL ROOF SIDE INNER GARNISH LH
Engage the guide.
Engage the 5 clips to install the roof side inner garnish LH.
62412B
23.INSTALL CENTER PILLAR UPPER GARNISH LH
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.
Engage the clip.
Install the center pillar upper garnish LH with the 2 screws.
62414A
24.INSTALL CENTER PILLAR LOWER GARNISH LH
Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.
73220
25.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
73233
26.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
62332A
27.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
| *1 | Alignment Mark (Red) |
Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
After installation, check that the corners fit correctly.
67918A
28.INSTALL REAR DOOR SCUFF PLATE LH
Engage the 6 claws to install the rear door scuff plate LH.
Engage the claws from the rear side of the scuff plate.
62471A
29.INSTALL ROOF SIDE INNER GARNISH RH
Use the same procedure as for the LH side.
62411B
30.INSTALL CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
62413A
31.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
73210
32.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
73233
33.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
Use the same procedure as for the LH side.
62331A
34.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
| *1 | Alignment Mark (Blue) |
Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
After installation, check that the corners fit correctly.
67917A
35.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
36.INSTALL REAR SEATBACK ASSEMBLY LH
37.INSTALL REAR SEATBACK ASSEMBLY RH
38.INSTALL REAR SIDE SEATBACK ASSEMBLY LH
39.INSTALL REAR SIDE SEATBACK ASSEMBLY RH
72693
40.INSTALL REAR SEAT CUSHION LOCK HOOK
41.INSTALL REAR SEAT CUSHION ASSEMBLY
62212
42.INSTALL FRONT PILLAR GARNISH LH
Remove the protective cover.
Make sure that the front pillar garnish clip is not damaged.
If there is any damage, replace the garnish clip with a new one.
Install the front pillar garnish clip to front pillar garnish LH.
Install the front pillar garnish clip so that it faces as shown in the illustration.
| *a | Correct | *b | Incorrect |
Engage the 2 guides as shown in the illustration.
Engage the 2 clips to install the front pillar garnish LH.
62312B
43.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
| *1 | Alignment Mark (Yellow) |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
After installation, check that the corners fit correctly.
62112A
44.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.
Install the cowl side trim sub-assembly LH with the clip.
67914
45.INSTALL FRONT DOOR SCUFF PLATE LH
Engage the 10 claws to install the front door scuff plate LH.
62211
46.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62311B
47.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
| *1 | Alignment Mark (White) |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
After installation, check that the corners fit correctly.
62111A
48.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
67913
49.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
50.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
51.INSPECT SRS WARNING LIGHT