Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR
RM2030EQ _58 Vehicle Interior _014669 SUPPLEMENTAL RESTRAINT SYSTEMS _0074629 SIDE AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 67914 3.REMOVE FRONT DOOR SCUFF PLATE

Hide 62312B 4.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.


Hide 67918A 5.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 6.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.


Hide 62414A 7.REMOVE CENTER PILLAR LOWER GARNISH

Hide 89860A 8.REMOVE SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the connector from the side airbag sensor assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

B279712C03
1.458,1.719 1.51,1.719 1.51,1.719 1.667,1.875 false 1.885,2.115 1.99,2.198 1.99,2.198 1.99,2.365 false 3.833,2.104 3.948,2.177 3.948,2.177 3.948,2.354 false 3.396,1.708 3.448,1.708 3.448,1.708 3.604,1.865 false 1.302,1.823 1.365,1.823 1.365,1.823 1.542,2 false 3.25,1.823 3.313,1.823 3.313,1.823 3.49,2 false 1.281,1.615 1.438,1.76 0.156,0.146 10 false *1 1.906,2.385 2.063,2.531 0.156,0.146 10 false *2 1.594,2.406 1.75,2.552 0.156,0.146 10 false *a 1.688,1.583 1.896,1.781 0.208,0.198 10 false *b 3.24,1.615 3.469,1.813 0.229,0.198 10 false *1 3.875,2.375 4.115,2.615 0.24,0.24 10 false *2 3.5,2.417 3.74,2.635 0.24,0.219 10 false *a 3.594,1.594 3.844,1.823 0.25,0.229 10 false *b 1.083,1.75 1.302,1.927 0.219,0.177 10 false (A) 3.031,1.74 3.25,1.917 0.219,0.177 10 false (A)
*1 White Housing Lock *2 Yellow CPA
*a Slide *b Push



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




d.

Remove the bolt and side airbag sensor assembly from the vehicle body.

NOTICE:

Loosen the bolt while holding the side airbag sensor assembly because the side airbag sensor assembly pin (stopper) is easily damaged.



e.

After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296256C05
5.01,0.51 5.292,0.792 0.281,0.281 10 false *b 1.792,0.51 2.063,0.792 0.271,0.281 10 false *a
*a Correct *b Incorrect