1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67914
3.REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.
Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.
Disengage the 6 claws (C) to remove the front door scuff plate LH.
62112A
4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Remove the clip.
Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.
62312B
5.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH.
62212
6.REMOVE FRONT PILLAR GARNISH LH
| *1 | Front Pillar Garnish Clip |
Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
Make the front pillar garnish LH hang down from the front pillar garnish clip.
While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.
Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
Protect the curtain shield airbag assembly.
Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
67913
7.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62111A
8.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
62311B
9.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62211
10.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
11.REMOVE REAR SEAT CUSHION ASSEMBLY
72693
12.REMOVE REAR SEAT CUSHION LOCK HOOK
13.REMOVE REAR SIDE SEATBACK ASSEMBLY LH
14.REMOVE REAR SIDE SEATBACK ASSEMBLY RH
15.REMOVE REAR SEATBACK ASSEMBLY LH
16.REMOVE REAR SEATBACK ASSEMBLY RH
67918A
17.REMOVE REAR DOOR SCUFF PLATE LH
Disengage the claw (A) in the direction indicated by the arrow (1) shown in the illustration.
Disengage the claw (B) in the direction indicated by the arrow (2) shown in the illustration.
Disengage the 4 claws (C) to remove the rear door scuff plate LH.
Disengage the claws from the front side of the rear door scuff plate LH.
62332A
18.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Remove the rear door opening trim weatherstrip LH.
73233
19.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
73220
20.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
62414A
21.REMOVE CENTER PILLAR LOWER GARNISH LH
Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.
62412B
22.REMOVE CENTER PILLAR UPPER GARNISH LH
Remove the 2 screws.
Disengage the clip.
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.
62472A
23.REMOVE ROOF SIDE INNER GARNISH LH
Disengage the 5 clips.
Disengage the guide and remove the roof side inner garnish LH.
67917A
24.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62331A
25.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
73233
26.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)
Use the same procedure as for the LH side.
73210
27.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62413A
28.REMOVE CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
62411B
29.REMOVE CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
62471A
30.REMOVE ROOF SIDE INNER GARNISH RH
Use the same procedure as for the LH side.
31.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL
32.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure as for the LH side.
33.REMOVE INSTRUMENT PANEL SAFETY PAD
87834
34.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
89943
35.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)
63650A
36.REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)
63650A
37.REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)
81240
38.REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)
81360T
39.REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)
74610A
40.REMOVE ASSIST GRIP SUB-ASSEMBLY (for LH Side)
| *1 | Protective Tape |
Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
Do not forcibly pry the assist grip covers to prevent them from being deformed.
Tape the screwdriver tip before use.
Disengage the 2 clips and remove the assist grip sub-assembly.
Remove the 2 clips from the vehicle body.
74610A
41.REMOVE ASSIST GRIP SUB-ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
74630E
42.REMOVE REAR ASSIST GRIP ASSEMBLY LH
| *1 | Protective Tape |
Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
Do not forcibly pry the assist grip covers to prevent them from being deformed.
Tape the screwdriver tip before use.
Disengage the 2 clips and remove the rear assist grip assembly LH.
Remove the 2 clips from the vehicle body.
74620C
43.REMOVE REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure as for the LH side.
63318C
44.REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
Remove the sliding roof opening trim moulding.
74325
45.REMOVE VISOR BRACKET COVER (for LH Side)
Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.
74320
46.REMOVE VISOR ASSEMBLY LH
Remove the 2 screws and visor assembly LH.
74325
47.REMOVE VISOR BRACKET COVER (for RH Side)
Use the same procedure as for the LH side.
74310
48.REMOVE VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74348
49.REMOVE VISOR HOLDER
Turn the visor holder approximately 45° and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder.
Use the same procedure for the other visor holder.
50.REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
w/ Rain Sensor:
Disconnect the connector from the rain sensor.
w/ EC Mirror:
Disconnect the connector from the inner rear view mirror.
Remove the bolt and disconnect the bracket from the front pillar RH.
| *A | w/ Digital Audio Broadcasting Antenna | - | - |
Disengage the 3 clamps from the front pillar RH.
Disengage the 4 clamps from the front pillar LH.
Disengage the 2 clamps and disconnect the connector from the rear pillar RH.
w/ Digital Audio Broadcasting Antenna:
Disengage the clamp and disconnect the connector from the rear pillar LH.
Remove the 2 clips.
Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.
Leave the 2 clips in the vehicle.
Remove the roof headlining assembly from the vehicle through the front passenger side door.
Do not damage the roof headlining assembly or body interior.
Remove the 2 clips from the vehicle body as shown in the illustration.
51.REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
w/ Rain Sensor:
Disconnect the connector from the rain sensor.
w/ EC Mirror:
Disconnect the connector from the inner rear view mirror.
Disconnect the connector from the sliding roof drive gear assembly.
| *A | w/ Digital Audio Broadcasting Antenna | - | - |
Remove the bolt and disconnect the bracket from the front pillar RH.
Disengage the 3 clamps from the front pillar RH.
Disengage the 4 clamps from the front pillar LH.
Disengage the 2 clamps and disconnect the connector from the rear pillar RH.
w/ Digital Audio Broadcasting Antenna:
Disengage the clamp and disconnect the connector from the rear pillar LH.
Remove the 2 clips.
Disengage the 2 fasteners.
Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.
Leave the 2 clips in the vehicle.
Remove the roof headlining assembly from the vehicle through the front passenger side door.
Do not damage the roof headlining assembly or body interior.
Remove the 2 clips from the vehicle body as shown in the illustration.