Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM2030EQ _58 Vehicle Interior _014672 HEATING / AIR CONDITIONING _0074654 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REASSEMBLY  


PROCEDURE

Hide 87050C 1.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

a.
E227210

Check that the slots, links and gears of the No. 1 air conditioning radiator damper servo sub-assembly are positioned in the correct orientation as shown in the illustration.


b.

Face the No. 1 air conditioning radiator damper servo sub-assembly contact surface of the air conditioning radiator assembly upward.


c.

Rotate the link of the air conditioning radiator assembly all the way to the left as shown in the illustration.

E219270


d.

Rotate the link of the air conditioning radiator assembly to the bottom as shown in the illustration and confirm that the mode switching duct hole is fully closed.

E219271
1.323,1.448 1.5,1.448 1.5,1.448 1.688,2.385 false 1.167,1.333 1.521,1.594 0.354,0.26 10 false *a
*a Mode Switching Duct Hole - -



e.

Rotate the lever of the air conditioning radiator assembly to the top as shown in the illustration.

E220372


f.

Rotate the link of the air conditioning radiator assembly to the in-line position as shown in the illustration.

E220373
5.354,0.333 4.958,0.396 false 4.792,0.302 5.094,0.615 0.302,0.313 10 false *a
*a In-line Position - -



g.
E219274
1.5,1.177 2.354,1.01 false 2.385,0.917 2.74,1.177 0.354,0.26 10 false *1
*1 Vinyl Tape


Wrap the upper and lower links with vinyl tape to hold them in the in-line position.


h.

Install the link of the No. 1 air conditioning radiator damper servo sub-assembly to the link guide pin (A) of the air conditioning radiator assembly as shown in the illustration.

E220374
3.219,0.26 3.365,0.26 3.365,0.26 3.573,0.563 false 1.292,1.448 0.906,1.448 0.906,1.448 1.115,2.677 false 1.438,2.625 1.094,3.729 false 5.74,1.521 5.885,1.521 5.885,1.521 6.26,2.865 false 6.469,2.958 5.885,3.74 false 3.052,0.167 3.365,0.396 0.313,0.229 10 false *1 1,3.729 1.344,4.01 0.344,0.281 10 false *2 5.792,3.719 6.146,4.01 0.354,0.292 10 false *a 1.313,1.344 1.688,1.625 0.375,0.281 10 false *b 5.583,1.417 5.927,1.667 0.344,0.25 10 false *c
*1 Guide *2 No. 1 Air Conditioning Radiator Damper Servo Sub-assembly
*a No. 1 Air Conditioning Radiator Damper Servo Sub-assembly Slot *b Link Guide Pin (A)
*c Link Guide Pin (B) - -



i.

Install the guide hole of the No. 1 air conditioning radiator damper servo sub-assembly to the guide pin of the air conditioning radiator assembly as shown in the illustration.


j.

Temporarily install the screw (up to 4 or 5 threads).

NOTICE:
·

Make sure that the link guide pin (B) is inserted in the No. 1 air conditioning radiator damper servo sub-assembly slot.

·

Avoid tilting the air conditioning radiator assembly during installation. This helps to prevent the guide pins from coming out of position.




k.
E219276

Lift the No. 1 air conditioning radiator damper servo sub-assembly slightly to create clearance.


l.

Move the air conditioning radiator assembly gear so that alignment holes of the No. 1 air conditioning radiator damper servo sub-assembly and air conditioning radiator assembly are aligned.

E219277
2.281,0.813 3.323,1.229 false 1.094,2.5 1.292,2.5 1.292,2.5 1.594,3.073 false 2.365,3.406 1.938,3.406 1.938,3.406 1.833,3.125 false 2.125,0.708 2.521,1.052 0.396,0.344 10 false *a 0.927,2.406 1.198,2.677 0.271,0.271 10 false *b 2.406,3.302 2.865,3.542 0.458,0.24 10 false *c
*a No. 1 Air Conditioning Radiator Damper Servo Sub-assembly Alignment Hole *b Air Conditioning Radiator Assembly Alignment Hole
*c Air Conditioning Radiator Assembly Alignment Gear Alignment Hole - -



m.
E219278

Insert a screwdriver into the aligned holes as shown in the illustration.


n.

Make sure that all the links and gears are in the positions shown in the illustration.

E220477
0.948,3.844 0.521,3.844 0.521,3.844 1.104,4.5 false 1.198,1.917 0.823,2.438 false 4.365,0.438 4.573,0.438 4.573,0.438 4.906,1.385 false 5.906,0.156 6.125,0.156 6.125,0.156 6.063,0.969 false 5.188,2.479 4.823,3.229 false 6.292,1.458 6.198,3.792 6.198,3.792 5.823,2.188 false 6.031,2.219 6.198,3.792 false 3.875,4.229 4.302,4.125 false 0.708,2.427 1.125,2.656 0.417,0.229 10 false *a 4.188,0.354 4.552,0.656 0.365,0.302 10 false *b 5.75,0.052 6.115,0.302 0.365,0.25 10 false *c 4.719,3.24 5.156,3.5 0.438,0.26 10 false *d 6.135,3.802 6.531,4.115 0.396,0.313 10 false *e 0.979,3.76 1.333,3.979 0.354,0.219 10 false *f 3.708,4.125 4.104,4.427 0.396,0.302 10 false *g
*a Screwdriver is inserted into alignment holes. *b Link guide pin is inserted.
*c Link is positioned to left side. *d Link is positioned at bottom.
*e Each link guide pin is inserted in its No. 1 air conditioning radiator damper servo sub-assembly slot. *f Lever is positioned at top.
*g Links are in-line. - -



o.
E219280

Push the loose fitting No. 1 air conditioning radiator damper servo sub-assembly into position.

NOTICE:
·

Make sure that the No. 1 air conditioning radiator damper servo sub-assembly is fully pushed into position.

·

After pushing the servos into position, keep them in place by holding them until the screws are installed.



HINT:

Push the No. 1 air conditioning radiator damper servo sub-assembly until a click sound is heard.



p.

Remove the screwdriver.


q.
E220478

Fully install the top screw, and then install the No. 1 air conditioning radiator damper servo sub-assembly with the 2 remaining screws.


r.

Remove the vinyl tape.


Hide 87107A 2.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

a.
E227203

Install the heater radiator unit sub-assembly to the air conditioner radiator assembly.


b.
E227201

Install the clamp with the screw.


c.
E227200

Engage the 3 claws and install the heater clamp.


Hide 87050D 3.INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

a.
E174875
2.469,1.052 3.031,2.656 false 2.969,2.667 3.313,2.927 0.344,0.26 10 false *1
*1 Reference Point


Using the reference point, install the No. 2 air conditioning radiator damper servo sub-assembly with the 2 screws.


Hide 88899L 5.INSTALL COOLING UNIT PARTS

a.
E185927
0.833,1.677 1.198,1.51 false 1.292,0.146 1.688,0.417 0.396,0.271 10 false *1 1.219,1.417 1.615,1.688 0.396,0.271 10 false *2
*1 Front of Vehicle
*2 Packing


Engage the 4 claws to install the cooling unit parts as shown in the illustration.

NOTICE:

Install the cooling unit parts to the No. 1 cooler evaporator sub-assembly after making sure that the packing is facing the front of the vehicle as shown in the illustration.



Hide 88501 6.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

a.
C129881

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces. Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

Compressor oil:

ND-OIL 8 or equivalent



b.
E227205

Install the No. 1 cooler evaporator sub-assembly to the blower assembly.


Hide 7.INSTALL BLOWER ASSEMBLY WITH COOLER EVAPORATOR SUB-ASSEMBLY

Hide 88515 8.INSTALL COOLER EXPANSION VALVE

a.
E227206

Using a 4 mm hexagon wrench, install the cooler expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


Hide 87201F 9.INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY (for RHD)

a.
E248530

Engage the guide and 2 claws, and install the No. 3 air duct sub-assembly as shown in the illustration.


Hide 82210K 10.INSTALL AIR CONDITIONING HARNESS ASSEMBLY

a.
E228262

Engage each clamp to install the air conditioning harness assembly.


b.

Connect each connector.


c.
E227196

Install the heater packing as shown in the illustration.


Hide 88897P 11.INSTALL ASPIRATOR

a.
E227232

Engage the 2 claws to install the aspirator.


Hide 88669A 12.INSTALL COOLER THERMISTOR HOSE

a.
E234890

Engage the clamp to install the cooler thermistor hose.


Hide 55840C 13.INSTALL NO. 6 HEATER TO REGISTER DUCT ASSEMBLY

a.
E227194

Engage the 2 guides and 2 claws to install the No. 6 heater to register duct assembly as shown in the illustration.


Hide 87201 14.INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY

a.
E227192

Engage the guide and 2 claws to install the No. 1 air duct sub-assembly as shown in the illustration.