82171
1.INSTALL NO. 1 ROOF WIRE
Apply double-sided tape as shown in the illustration.
| *A | w/o Sliding Roof without Vanity Light | *B | w/o Sliding Roof with Vanity Light |
| *C | w/ Sliding Roof | *D | Tape Attachment Locations (Reference) |
| *1 | Double-sided Tape | *2 | Marking |
1 mm (0.0394 in.)
10 mm (0.394 in.)
20 mm (0.787 in.)
Peel off the release paper from the double-sided tape.
Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.
Align the pink marking tape (A) on the No. 1 roof wire with the vehicle front side tab on the roof headlining.
| *A | w/o Sliding Roof without Vanity Light | *B | w/o Sliding Roof with Vanity Light |
| *C | w/ Sliding Roof | - | - |
| *1 | Pink Marking Tape (A) | *2 | Pink Marking Tape (B) |
| *3 | Pink Marking Tape (C) | *4 | Pink Marking Tape (D) |
| *5 | Marking | *6 | Adjustment Area |
w/ Vanity Light:
Turn the visor connector LH clockwise approximately 45° to install it to the roof headlining assembly.
Align the edge of the pink marking tape (B) on the No. 1 roof wire with the markings on the roof headlining.
Attach the No. 1 roof wire, starting from the pink marking tape (B) to the pink marking tape (A) while aligning it with the double-sided tape.
Securely attach the No. 1 roof wire.
If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.
w/ Vanity Light:
Turn the visor connector RH clockwise approximately 45° to install it to the roof headlining assembly.
Attach the No. 1 roof wire, starting from the visor connector RH to the pink marking tape (B) while aligning it with the double-sided tape.
Securely attach the No. 1 roof wire.
If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.
Attach the No. 1 roof wire, starting from the visor connector RH to the pink marking tape (B) while aligning it with the double-sided tape.
Attach the No. 1 roof wire, starting from the pink marking tape (C) to the pink marking tape (B) while aligning it with the double-sided tape.
Securely attach the No. 1 roof wire.
If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.
Align the edge of the pink marking tape (D) on the No. 1 roof wire with the markings on the roof headlining.
Attach the No. 1 roof wire, starting from the pink marking tape (A) to the pink marking tape (D) while aligning it with the double-sided tape.
Securely attach the No. 1 roof wire.
If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.
Secure the extra length of the No. 1 roof wire in the adjustment area.
Apply adhesive tape by aligning it with the markings on the roof headlining as shown in the illustration.
| *A | w/o Sliding Roof without Vanity Light | *B | w/o Sliding Roof with Vanity Light |
| *C | Tape Attachment Location (Reference) | *D | Tape Attachment Location (Reference) |
| *E | w/o EC Mirror | *F | for LHD with EC Mirror |
| *G | for RHD with Rain Sensor | - | - |
| *1 | Adhesive Tape | *2 | Marking |
20 mm (0.787 in.)
80 mm (3.15 in.)
86101J
2.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/o Digital Audio Broadcasting Antenna)
86101J
3.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/ Digital Audio Broadcasting Antenna)
63342
4.INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)
Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the pad using hot-melt glue as shown in the illustration.
| *1 | Marking | *2 | Hot-melt Glue |
Securely attach the No. 2 roof silencer pad before the hot-melt glue cools.
63341
5.INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)
Align the markings on the roof headlining assembly with the 3 No. 1 roof silencer pads and install the pads using hot-melt glue as shown in the illustration.
| *1 | Marking | *2 | Hot-melt Glue |
Securely attach the No. 1 roof silencer pad before the hot-melt glue cools.
81340
6.INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)
Install the vanity light assembly.
Click hereVehicle Interior>LIGHTING (INT)>VANITY LIGHT>INSTALLATION
Use the same procedure for the other vanity light.