Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM2030EQ _59 Vehicle Exterior _014677 DOOR / HATCH _0074691 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B280381C13
0.698,0.146 1.083,0.396 0.385,0.25 10 false *1 2.51,0.146 2.833,0.396 0.323,0.25 10 false *2
*1 Centering Bolt
*2 Standard Bolt


HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSPECT FRONT DOOR

a.

Check that the clearance measurements of areas *a through *p are within each standard range.

B281696E01
1.24,1.01 1.521,1.271 0.281,0.26 10 false *a 1.448,1.74 1.729,1.99 0.281,0.25 10 false *b 2.865,0.896 3.302,1.25 0.438,0.354 10 false *c 2.99,1.813 3.281,2.094 0.292,0.281 10 false *d 4.396,0.833 4.75,1.115 0.354,0.281 10 false *e 4.406,1.719 4.813,2.073 0.406,0.354 10 false *f 6.458,2.885 6.854,3.219 0.396,0.333 10 false *g 6.417,4.5 6.708,4.792 0.292,0.292 10 false *h 6.854,4.208 7.094,4.49 0.24,0.281 10 false *i 4.917,5.698 5.219,5.948 0.302,0.25 10 false *j 5.302,5.406 5.667,5.667 0.365,0.26 10 false *k 3.813,5.281 4.094,5.552 0.281,0.271 10 false *l 1.625,5.615 2.01,5.948 0.385,0.333 10 false *m 2.188,5.24 2.635,5.583 0.448,0.344 10 false *n 0.479,3.708 0.771,4.021 0.292,0.313 10 false *o 1.104,3.469 1.573,3.948 0.469,0.479 10 false *p

Standard Clearance
Area Measurement Area Measurement
*a 3.35 to 6.35 mm (0.132 to 0.250 in.) *b 9.0 to 12.0 mm (0.354 to 0.472 in.)
*c 3.35 to 6.35 mm (0.132 to 0.250 in.) *d 1.7 to 4.7 mm (0.0669 to 0.185 in.)
*e 3.35 to 6.35 mm (0.132 to 0.250 in.) *f 1.0 to 4.0 mm (0.0394 to 0.157 in.)
*g 2.3 to 6.3 mm (0.0906 to 0.248 in.) *h 2.96 to 4.64 mm (0.115 to 0.182 in.)
*i -0.84 to 0.84 mm (-0.0331 to 0.0331 in.) *j 2.96 to 4.64 mm (0.115 to 0.182 in.)
*k -0.84 to 0.84 mm (-0.0331 to 0.0331 in.) *l 2.9 to 7.1 mm (0.114 to 0.280 in.)
*m 2.3 to 4.7 mm (0.0906 to 0.185 in.) *n -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)
*o 2.3 to 4.7 mm (0.0906 to 0.185 in.) *p -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)


Hide 2.REMOVE FRONT WHEEL

Hide 53852K 3.REMOVE FRONT WHEEL OPENING EXTENSION PAD

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>REMOVAL


Hide 53876A 4.REMOVE FRONT FENDER LINER

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>REMOVAL


Hide 53883K 5.REMOVE FRONT FENDER SEAL

a.
B280591

Disengage the 3 clips and remove the front fender seal.


Hide 6.ADJUST FRONT DOOR

NOTICE:

Make sure to turn the ignition switch off when adjusting door lock strikers.


a.

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  

B334512


b.

Tighten the hinge bolts on the vehicle body after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B280382

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 53883K 7.INSTALL FRONT FENDER SEAL

a.
B280591

Install the front fender seal with 3 new clips.


Hide 53876A 8.INSTALL FRONT FENDER LINER

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>INSTALLATION


Hide 53852K 9.INSTALL FRONT WHEEL OPENING EXTENSION PAD

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>INSTALLATION