Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM2030EQ _59 Vehicle Exterior _014679 WIPER / WASHER _0074707 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rain Sensor Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a signal from the rain sensor to control the auto wiper system.

WIRING DIAGRAM

E226326E01
4.934,2.582 5.373,2.759 0.439,0.177 10 I72 4.934,2.754 7.072,2.94 2.138,0.186 10 Windshield Wiper Relay Assembly 2.881,2.63 3.246,2.806 0.365,0.177 10 S1 2.881,2.801 3.706,2.988 0.825,0.186 10 Rain Sensor 3.789,1.317 3.992,1.484 0.203,0.167 10 1 2.97,2.034 3.22,2.201 0.25,0.167 10 ES 3.368,1.442 3.691,1.609 0.323,0.167 10 MPX 2.957,0.877 3.256,1.044 0.299,0.167 10 SIG 0.278,0.857 1.285,1.219 1.007,0.361 10 from IG1 NO. 2 Relay 1.762,1.016 2.8,1.201 1.038,0.186 10 ECU-IG1 NO. 2 5.411,1.442 5.895,1.609 0.484,0.167 10 MPX1 5.143,1.317 5.346,1.484 0.203,0.167 10 14 2.774,0.78 2.905,0.947 0.131,0.167 10 4 2.774,1.933 2.905,2.1 0.131,0.167 10 2 0.892,3.261 2.516,3.448 1.624,0.186 10 : Lin Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - RAIN SENSOR)
a.

Disconnect the I72 windshield wiper relay assembly connector.


b.

Disconnect the S1 rain sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-14 (MPX1) - S1-1 (MPX) Always Below 1 Ω
S1-1 (MPX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BATTERY AND BODY GROUND)
a.
E169141C13
1.51,1.438 1.906,1.708 0.396,0.271 2.042,2.458 2.563,1.906 false 1.563,2.427 1.031,1.865 false 1.625,1.49 2.104,1.781 0.479,0.292 10 false S1 0.854,1.677 1.292,2 0.438,0.323 10 false ES 2.479,1.688 2.948,2.021 0.469,0.333 10 false SIG 0.219,0.167 0.583,0.427 0.365,0.26 10 false *a
*a Front view of wire harness connector
(to Rain Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S1-4 (SIG) - S1-2 (ES) Ignition switch ON 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S1-2 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT RAIN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RAIN SENSOR
a.
E141656C13
0.563,1.615 1.031,1.875 0.469,0.26 1.979,1.979 2.292,1.563 false 1.688,1.417 1.813,1.979 false 0.219,0.167 0.76,0.677 0.542,0.51 10 false *a 2.198,1.375 2.813,1.75 0.615,0.375 10 false MPX 1.542,1.229 1.958,1.438 0.417,0.208 10 false ES 0.698,1.656 1.406,2.104 0.708,0.448 10 false S1
*a Component with harness connected
(Rain Sensor)


Reconnect the S1 rain sensor connector.


b.

Connect an oscilloscope to the rain sensor connector.


c.

Check for pulses.

OK:
Tester Connection Condition Specified Condition
S1-1 (MPX) - S1-2 (ES) Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG