Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2030EQ _58 Vehicle Interior _014669 SUPPLEMENTAL RESTRAINT SYSTEMS _0074620 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1612/83  Lost Communication with Front Airbag Sensor RH  B1613/83  Front Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1612/83 Lost Communication with Front Airbag Sensor RH
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor RH circuit.

·

Front airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1613/83 Front Airbag Sensor RH Initialization Incomplete
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor RH circuit.

·

Front airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode

WIRING DIAGRAM

C244889E10
3.458,0.906 3.875,1.354 0.417,0.448 10 IA5 3.51,0.719 3.927,1.167 0.417,0.448 10 2 3.458,2.083 3.875,2.563 0.417,0.479 10 IA5 3.51,1.896 3.781,2.177 0.271,0.281 10 1 5.135,0.813 5.469,1.188 0.333,0.375 10 29 5.135,1.99 5.458,2.396 0.323,0.406 10 27 5.396,0.896 5.792,1.281 0.396,0.385 10 +SR 5.396,2.073 5.76,2.458 0.365,0.385 10 -SR 1.854,0.813 2.229,1.219 0.375,0.406 10 2 1.854,1.99 2.208,2.458 0.354,0.469 10 1 1.479,0.896 1.969,1.292 0.49,0.396 10 +SR 1.51,2.073 2.031,2.542 0.521,0.469 10 -SR 0.438,2.927 0.906,3.385 0.469,0.458 10 A58 0.438,3.083 2.063,3.406 1.625,0.323 10 Front Airbag Sensor RH 5.219,2.927 5.531,3.219 0.313,0.292 10 I47 5.219,3.083 6.833,3.406 1.615,0.323 10 Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)
a.
C238384C01
0.792,0.531 1.125,0.75 0.333,0.219 0.427,3.615 0.781,3.854 0.354,0.24 1.938,0.854 1.76,1.063 false 2.115,0.844 2.323,1.073 false 1.156,3.74 0.854,4.156 false 1.323,3.74 1.667,4.167 false 2.042,1.125 2.042,1.281 false 0.854,2.229 1.333,2.708 0.479,0.479 10 F 1.094,2.24 1.563,2.76 0.469,0.521 10 E 1.438,2.24 1.813,2.719 0.375,0.479 10 D 1.594,2.24 2.031,2.833 0.438,0.594 10 C 1.938,2.229 2.354,2.719 0.417,0.49 10 B 2.177,2.24 2.49,2.667 0.313,0.427 10 A 0.479,2.229 0.896,2.615 0.417,0.385 10 *1 2.625,2.24 2.938,2.677 0.313,0.438 10 *2 0.656,0.188 0.958,0.479 0.302,0.292 10 *a 0.354,3.198 0.75,3.521 0.396,0.323 10 *b 1.5,1 1.948,1.385 0.448,0.385 10 -SR 2.375,1.01 2.844,1.417 0.469,0.406 10 +SR 0.479,3.656 1,4.083 0.521,0.427 10 A58 1.979,1.302 2.333,1.625 0.354,0.323 10 *3 0.698,4.198 1.229,4.521 0.531,0.323 10 -SR 1.573,4.208 2.052,4.542 0.479,0.333 10 +SR 0.875,0.563 1.208,0.99 0.333,0.427 10 I47
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor RH)


Connect the connectors that link the engine room main wire and instrument panel wire.


b.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-2 (+SR) - A58-1 (-SR) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)

NG

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)
a.
C238385C03
0.438,2.302 0.781,2.552 0.344,0.25 1.146,2.438 0.958,2.854 false 1.323,2.438 1.521,2.875 false 0.833,0.927 1.5,1.438 0.667,0.51 10 F 1.083,0.927 1.573,1.448 0.49,0.521 10 E 1.427,0.938 1.948,1.49 0.521,0.552 10 D 1.583,0.938 2,1.49 0.417,0.552 10 C 1.927,0.927 2.313,1.448 0.385,0.521 10 B 2.167,0.927 2.469,1.333 0.302,0.406 10 A 0.448,0.927 0.99,1.396 0.542,0.469 10 *1 2.635,0.969 3.021,1.49 0.385,0.521 10 *2 0.354,1.896 0.76,2.24 0.406,0.344 10 *a 0.49,2.344 0.865,2.688 0.375,0.344 10 A58 0.802,2.885 1.281,3.26 0.479,0.375 10 -SR 1.385,2.896 1.906,3.219 0.521,0.323 10 +SR
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor RH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-2 (+SR) - A58-1 (-SR) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)
a.
C238385C03
0.438,2.302 0.781,2.552 0.344,0.25 1.146,2.438 0.958,2.854 false 1.323,2.438 1.521,2.875 false 0.833,0.927 1.5,1.438 0.667,0.51 10 F 1.083,0.927 1.573,1.448 0.49,0.521 10 E 1.427,0.938 1.948,1.49 0.521,0.552 10 D 1.583,0.938 2,1.49 0.417,0.552 10 C 1.927,0.927 2.313,1.448 0.385,0.521 10 B 2.167,0.927 2.469,1.333 0.302,0.406 10 A 0.448,0.927 0.99,1.396 0.542,0.469 10 *1 2.635,0.969 3.021,1.49 0.385,0.521 10 *2 0.354,1.896 0.76,2.24 0.406,0.344 10 *a 0.49,2.344 0.865,2.688 0.375,0.344 10 A58 0.802,2.885 1.281,3.26 0.479,0.375 10 -SR 1.385,2.896 1.906,3.219 0.521,0.323 10 +SR
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-2 (+SR) - Body ground Ignition switch ON Below 1 V
A58-1 (-SR) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)
a.
C238385C03
0.438,2.302 0.781,2.552 0.344,0.25 1.146,2.438 0.958,2.854 false 1.323,2.438 1.521,2.875 false 0.833,0.927 1.5,1.438 0.667,0.51 10 F 1.083,0.927 1.573,1.448 0.49,0.521 10 E 1.427,0.938 1.948,1.49 0.521,0.552 10 D 1.583,0.938 2,1.49 0.417,0.552 10 C 1.927,0.927 2.313,1.448 0.385,0.521 10 B 2.167,0.927 2.469,1.333 0.302,0.406 10 A 0.448,0.927 0.99,1.396 0.542,0.469 10 *1 2.635,0.969 3.021,1.49 0.385,0.521 10 *2 0.354,1.896 0.76,2.24 0.406,0.344 10 *a 0.49,2.344 0.865,2.688 0.375,0.344 10 A58 0.802,2.885 1.281,3.26 0.479,0.375 10 -SR 1.385,2.896 1.906,3.219 0.521,0.323 10 +SR
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-2 (+SR) - Body ground Always 1 MΩ or higher
A58-1 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT AIRBAG SENSOR RH

NG

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR RH
a.
C238386C02
2.083,1.01 2.448,1.5 0.365,0.49 10 A 1.927,1.01 2.427,1.479 0.5,0.469 10 B 1.583,1.01 1.969,1.521 0.385,0.51 10 C 1.427,1.01 1.844,1.583 0.417,0.573 10 D 1.083,1.01 1.531,1.667 0.448,0.656 10 E 0.938,1.01 1.521,1.75 0.583,0.74 10 F 0.563,1.021 1.125,1.594 0.563,0.573 10 *1 2.542,1.031 2.885,1.563 0.344,0.531 10 *2
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the front airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. A
DTC B1617/84 or B1618/84 is output. B
DTC B1612/83 or B1613/83 is output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the front airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C238388C04
0.49,2.198 0.833,2.427 0.344,0.229 1.354,2.333 1.052,2.75 false 1.469,2.333 1.802,2.75 false 1.24,0.906 1.24,1.156 false 1.823,0.771 1.823,0.365 1.823,0.365 1.667,0.365 false 0.792,0.76 1.135,1.281 0.344,0.521 10 F 1.031,0.76 1.365,1.208 0.333,0.448 10 E 1.375,0.76 1.635,1.146 0.26,0.385 10 D 1.615,0.771 1.875,1.146 0.26,0.375 10 C 1.958,0.771 2.26,1.25 0.302,0.479 10 B 2.208,0.771 2.5,1.198 0.292,0.427 10 A 0.396,0.771 0.979,1.292 0.583,0.521 10 *1 2.677,0.781 3,1.146 0.323,0.365 10 *2 1.51,0.292 1.823,0.688 0.313,0.396 10 *4 1.177,1.188 1.521,1.552 0.344,0.365 10 *3 0.375,1.75 0.719,2.115 0.344,0.365 10 *a 0.563,2.229 0.948,2.583 0.385,0.354 10 IA5 1.708,2.781 2.188,3.177 0.479,0.396 10 +SR 0.896,2.781 1.344,3.125 0.448,0.344 10 -SR
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IA5-2 (+SR) - Body ground Always 1 MΩ or higher
IA5-1 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C238388C04
0.49,2.198 0.833,2.427 0.344,0.229 1.354,2.333 1.052,2.75 false 1.469,2.333 1.802,2.75 false 1.24,0.906 1.24,1.156 false 1.823,0.771 1.823,0.365 1.823,0.365 1.667,0.365 false 0.792,0.76 1.135,1.281 0.344,0.521 10 F 1.031,0.76 1.365,1.208 0.333,0.448 10 E 1.375,0.76 1.635,1.146 0.26,0.385 10 D 1.615,0.771 1.875,1.146 0.26,0.375 10 C 1.958,0.771 2.26,1.25 0.302,0.479 10 B 2.208,0.771 2.5,1.198 0.292,0.427 10 A 0.396,0.771 0.979,1.292 0.583,0.521 10 *1 2.677,0.781 3,1.146 0.323,0.365 10 *2 1.51,0.292 1.823,0.688 0.313,0.396 10 *4 1.177,1.188 1.521,1.552 0.344,0.365 10 *3 0.375,1.75 0.719,2.115 0.344,0.365 10 *a 0.563,2.229 0.948,2.583 0.385,0.354 10 IA5 1.708,2.781 2.188,3.177 0.479,0.396 10 +SR 0.896,2.781 1.344,3.125 0.448,0.344 10 -SR
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
IA5-2 (+SR) - Body ground Ignition switch ON Below 1 V
IA5-1 (-SR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C238388C04
0.49,2.198 0.833,2.427 0.344,0.229 1.354,2.333 1.052,2.75 false 1.469,2.333 1.802,2.75 false 1.24,0.906 1.24,1.156 false 1.823,0.771 1.823,0.365 1.823,0.365 1.667,0.365 false 0.792,0.76 1.135,1.281 0.344,0.521 10 F 1.031,0.76 1.365,1.208 0.333,0.448 10 E 1.375,0.76 1.635,1.146 0.26,0.385 10 D 1.615,0.771 1.875,1.146 0.26,0.375 10 C 1.958,0.771 2.26,1.25 0.302,0.479 10 B 2.208,0.771 2.5,1.198 0.292,0.427 10 A 0.396,0.771 0.979,1.292 0.583,0.521 10 *1 2.677,0.781 3,1.146 0.323,0.365 10 *2 1.51,0.292 1.823,0.688 0.313,0.396 10 *4 1.177,1.188 1.521,1.552 0.344,0.365 10 *3 0.375,1.75 0.719,2.115 0.344,0.365 10 *a 0.563,2.229 0.948,2.583 0.385,0.354 10 IA5 1.708,2.781 2.188,3.177 0.479,0.396 10 +SR 0.896,2.781 1.344,3.125 0.448,0.344 10 -SR
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IA5-2 (+SR) - IA5-1 (-SR) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C238387C01
0.865,0.5 1.208,0.74 0.344,0.24 0.396,3.563 0.76,3.802 0.365,0.24 2.042,0.823 1.854,1.031 false 2.219,0.823 2.417,1.052 false 2.125,1.083 2.125,1.271 false 1.229,2.385 1.229,2.646 false 1.833,2.24 1.833,1.854 1.833,1.854 1.677,1.854 false 1.198,3.708 0.906,4.125 false 1.313,3.708 1.646,4.125 false 0.792,2.229 1.063,2.698 0.271,0.469 10 F 1.031,2.229 1.302,2.542 0.271,0.313 10 E 1.375,2.229 1.688,2.615 0.313,0.385 10 D 1.615,2.229 2.031,2.708 0.417,0.479 10 C 1.958,2.229 2.292,2.698 0.333,0.469 10 B 2.198,2.229 2.521,2.667 0.323,0.438 10 A 1.521,1.781 1.865,2.146 0.344,0.365 10 *4 1.167,2.667 1.49,3.073 0.323,0.406 10 *3 1.594,0.969 2.146,1.396 0.552,0.427 10 -SR 2.479,0.99 2.99,1.365 0.51,0.375 10 +SR 0.958,0.542 1.292,0.906 0.333,0.365 10 I47 0.479,3.594 0.875,4 0.396,0.406 10 IA5 0.396,2.229 0.781,2.677 0.385,0.448 10 *1 2.667,2.25 3,2.656 0.333,0.406 10 *2 0.656,0.198 1.01,0.604 0.354,0.406 10 *a 0.375,3.198 0.844,3.563 0.469,0.365 10 *b 1.563,4.167 2.031,4.448 0.469,0.281 10 +SR 0.75,4.156 1.25,4.479 0.5,0.323 10 -SR 2.063,1.292 2.333,1.625 0.271,0.333 10 *5
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IA5-2 (+SR) - IA5-1 (-SR) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE