The front airbag sensor LH circuit consists of the airbag sensor assembly and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1617/84 | Lost Communication with Front Airbag Sensor LH | ·
The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit. ·
Front airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor LH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B1618/84 | Front Airbag Sensor LH Initialization Incomplete | ·
The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit. ·
Front airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor LH ·
Airbag sensor assembly |
Does not apply to test/check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Front Airbag Sensor LH) |
Connect the connectors that link the engine room main wire and instrument panel wire.
Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A12-2 (+SL) - A12-1 (-SL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Front Airbag Sensor LH) |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A12-2 (+SL) - A12-1 (-SL) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Front Airbag Sensor LH) |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A12-2 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| A12-1 (-SL) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Front Airbag Sensor LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A12-2 (+SL) - Body ground | Always | 1 MΩ or higher |
| A12-1 (-SL) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the airbag sensor assembly.
Interchange the front airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. | A |
| DTC B1617/84 or B1618/84 is output. | B |
| DTC B1612/83 or B1613/83 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the front airbag sensor LH and RH to their original positions and connect the connectors.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
Disconnect the instrument panel wire connector from the engine room main wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IA5-3 (+SL) - Body ground | Always | 1 MΩ or higher |
| IA5-4 (-SL) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IA5-3 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| IA5-4 (-SL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Engine Room Main Wire) |
Disconnect the instrument panel wire connector from the engine room main wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IA5-3 (+SL) - IA5-4 (-SL) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire |
| *4 | Instrument Panel Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Engine Room Main Wire) |
Disconnect the instrument panel wire connector from the engine room main wire.
The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IA5-3 (+SL) - IA5-4 (-SL) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG