Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2030EQ _58 Vehicle Interior _014669 SUPPLEMENTAL RESTRAINT SYSTEMS _0074620 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825/56  Short in Side Squib LH Circuit  B1826/56  Open in Side Squib LH Circuit  B1827/56  Short to GND in Side Squib LH Circuit  B1828/56  Short to B+ in Side Squib LH Circuit  


DESCRIPTION

The side squib LH circuit consists of the airbag sensor assembly and front seat airbag assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1825/56 Short in Side Squib LH Circuit
·

The airbag sensor assembly receives a line short circuit signal in the side squib LH circuit during primary check.

·

Side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Airbag sensor assembly


Applies to check mode
B1826/56 Open in Side Squib LH Circuit
·

The airbag sensor assembly receives an open circuit signal in the side squib LH circuit.

·

Side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Airbag sensor assembly


Applies to check mode
B1827/56 Short to GND in Side Squib LH Circuit
·

The airbag sensor assembly receives a short circuit to ground signal in the side squib LH circuit.

·

Side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Airbag sensor assembly


Applies to check mode
B1828/56 Short to B+ in Side Squib LH Circuit
·

The airbag sensor assembly receives a short circuit to B+ signal in the side squib LH circuit.

·

Side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Airbag sensor assembly


Applies to check mode

WIRING DIAGRAM

C287107E02
0.729,2.688 2.823,2.885 2.094,0.198 10 false Front Seat Airbag Assembly LH 0.729,2.531 1.188,2.729 0.458,0.198 10 false Nz1 0.719,2.896 1.802,3.115 1.083,0.219 10 false (Side Squib LH) 4.719,3.208 6.292,3.448 1.573,0.24 10 false Airbag Sensor Assembly 4.708,3.052 5.021,3.25 0.313,0.198 10 false N5 1.958,1.052 2.573,1.25 0.615,0.198 10 false SFL+ 1.979,1.896 2.594,2.094 0.615,0.198 10 false SFL- 4.75,2 5.365,2.198 0.615,0.198 10 false SFL- 4.729,1.146 5.344,1.344 0.615,0.198 10 false SFL+ 2.438,1.052 2.594,1.25 0.156,0.198 10 false 1 2.438,1.896 2.594,2.094 0.156,0.198 10 false 2 4.5,1.052 4.656,1.25 0.156,0.198 10 false 1 4.531,1.896 4.688,2.094 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C238350C01
0.521,1.021 0.521,1.635 false 1.385,0.896 1.385,0.469 1.385,0.469 1.615,0.469 false 0.646,0.875 0.865,1.167 0.219,0.292 10 D 1.052,0.875 1.417,1.281 0.365,0.406 10 C 1.625,0.875 1.938,1.26 0.313,0.385 10 B 2.021,0.875 2.281,1.26 0.26,0.385 10 A 2.469,1.188 2.771,1.625 0.302,0.438 10 *2 0.448,1.656 0.896,1.99 0.448,0.333 10 *1 1.646,0.385 1.969,0.677 0.323,0.292 10 *3
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat airbag assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat airbag assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT AIRBAG ASSEMBLY LH (SIDE SQUIB LH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT AIRBAG ASSEMBLY LH (SIDE SQUIB LH)
a.
C238351C01
0.354,2.24 0.729,2.469 0.375,0.229 1.823,2.531 2.01,2.531 false 0.656,0.635 0.656,1 false 0.771,0.479 1.198,0.833 0.427,0.354 10 D 1.156,0.479 1.615,0.844 0.458,0.365 10 C 1.708,0.479 2.052,0.729 0.344,0.25 10 B 1.865,0.49 2.271,0.781 0.406,0.292 10 A 2.302,0.813 2.688,1.073 0.385,0.26 10 *2 0.604,1.01 0.969,1.365 0.365,0.354 10 *1 0.354,1.833 0.688,2.083 0.333,0.25 10 *a 2.063,2.448 2.5,2.771 0.438,0.323 10 SST 0.427,2.271 0.813,2.542 0.385,0.271 10 Nz1
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)


Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag assembly LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.


HINT:

Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
C238352C04
0.469,2.354 0.823,2.583 0.354,0.229 1.406,2.594 1.115,2.854 false 1.875,2.844 1.583,2.583 false 0.563,0.729 0.563,1.177 false 1.375,0.583 1.375,0.198 1.375,0.198 1.531,0.198 false 0.677,0.573 0.896,0.802 0.219,0.229 10 false D 1.063,0.573 1.354,0.854 0.292,0.281 10 false C 1.583,0.573 1.865,0.958 0.281,0.385 10 false B 1.979,0.573 2.208,0.906 0.229,0.333 10 false A 2.406,0.875 2.75,1.25 0.344,0.375 10 false *2 0.5,1.177 0.875,1.469 0.375,0.292 10 false *1 0.313,1.719 0.604,2.01 0.292,0.292 10 false *a 1.854,2.854 2.354,3.125 0.5,0.271 10 false SFL- 0.813,2.854 1.281,3.083 0.469,0.229 10 false SFL+ 1.552,0.115 1.906,0.438 0.354,0.323 10 false *3 0.531,2.385 1.031,2.813 0.5,0.427 10 false Nz1
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)


Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Nz1-1 (SFL+) - Body ground Ignition switch ON Below 1 V
Nz1-2 (SFL-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Nz1-1 (SFL+) - Nz1-2 (SFL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Nz1-1 (SFL+) - Body ground Always 1 MΩ or higher
Nz1-2 (SFL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Nz1-1 (SFL+) - Nz1-2 (SFL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238353C01
0.802,0.833 0.802,1.156 false 0.938,0.708 1.542,1.438 0.604,0.729 10 false D 1.083,0.708 1.49,1.177 0.406,0.469 10 false C 1.594,0.708 1.885,1.094 0.292,0.385 10 false B 1.75,0.708 2.073,1 0.323,0.292 10 false A 2.188,1.021 2.49,1.354 0.302,0.333 10 false *2 0.74,1.167 1.115,1.521 0.375,0.354 10 false *1
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat airbag assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.


HINT:

Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG