Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0076659 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Warning Buzzer Circuit  


DESCRIPTION

This circuit consists of the No. 1 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The battery voltage supplied through the buzzer is grounded inside the clearance warning ECU assembly using a pulsed digital pattern, producing sound. The ECU operates the buzzer using a sound pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E220929E12
1.979,1.354 2.219,1.604 0.24,0.25 10 1 3.271,1.354 3.531,1.708 0.26,0.354 10 2 1.635,2.021 1.917,2.177 0.281,0.156 10 I54 1.635,2.198 3.896,2.438 2.26,0.24 10 No. 1 Clearance Warning Buzzer 4.198,2.021 4.479,2.177 0.281,0.156 10 I82 4.198,2.188 6.5,2.5 2.302,0.313 10 Clearance Warning ECU Assembly 4.698,0.615 5.146,0.979 0.448,0.365 10 14 4.948,0.708 5.396,1.01 0.448,0.302 10 BBZ 4.698,1.354 5.125,1.677 0.427,0.323 10 13 4.948,1.438 5.438,1.813 0.49,0.375 10 ER 2.146,1.354 2.531,1.604 0.385,0.25 10 Z+ 3.052,1.354 3.438,1.615 0.385,0.26 10 Z-

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Sonar > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the engine switch is on (IG)
Body Electrical > Clearance Sonar > Active Test
Tester Display
Buzzer
50004 170 4
OK:

The No. 1 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 1 CLEARANCE WARNING BUZZER)
a.

Disconnect the I54 No. 1 clearance warning buzzer connector.


b.

Disconnect the I82 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I82-14 (BBZ) - I54-1 (Z+) Always Below 1 Ω
I82-13 (ER) - I54-2 (Z-)
I82-14 (BBZ) - Body ground 10 kΩ or higher
I82-13 (ER) - Body ground



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER
a.

Replace the No. 1 clearance warning buzzer with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Clearance Sonar / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Sonar > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer No. 1 clearance warning buzzer Operate or Stop Confirm that the vehicle is stopped and the engine switch is on (IG)
Body Electrical > Clearance Sonar > Active Test
Tester Display
Buzzer
50004 170 4
OK:

The No. 1 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

END (NO. 1 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG