This DTC is stored when there is an open or short circuit in the communication line between the front sensors and the ECU, or when there is a malfunction in a front sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AEC | Front Sensor Communication Malfunction | An open or short circuit in the communication line between the front sensors and ECU or a malfunction in a front sensor during initialization mode after the engine switch is turned on (IG). | ·
Front ultrasonic sensor circuit ·
Clearance warning ECU assembly |
Check for DTCs.
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AEC is output | A |
| No DTCs are output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the I82 clearance warning ECU assembly connector.
Disconnect the A5 No. 1 ultrasonic sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I82-4 (BOF) - A5-1 (BI) | Always | Below 1 Ω |
| I82-8 (SOF) - A5-3 (SI) | Always | Below 1 Ω |
| I82-6 (E5) - A5-5 (EI) | Always | Below 1 Ω |
| I82-4 (BOF) - Body ground | Always | 10 kΩ or higher |
| I82-8 (SOF) - Body ground | Always | 10 kΩ or higher |
| I82-6 (E5) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A56 No. 1 ultrasonic sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-2 (BO) - A56-1 (BI) | Always | Below 1 Ω |
| A5-4 (SO) - A56-3 (SI) | Always | Below 1 Ω |
| A5-6 (EO) - A56-5 (EI) | Always | Below 1 Ω |
| A5-2 (BO) - Body ground | Always | 10 kΩ or higher |
| A5-4 (SO) - Body ground | Always | 10 kΩ or higher |
| A5-6 (EO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(No. 1 Ultrasonic Sensor (Front Left Sensor)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (BI) - 5 (EI) | Always | 10 kΩ or higher |
| 1 (BI) - 2 (BO) | Always | 10 kΩ or higher |
| 3 (SI) - 4 (SO) | Always | Below 1 Ω |
| 5 (EI) - 6 (EO) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front Side)>REMOVAL
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE1
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AEC is output | A |
| No DTCs are output | B |
A
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE4
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AEC is output | A |
| No DTCs are output | B |
A
B