Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM2030EQ _59 Vehicle Exterior _014678 MIRROR (EXT) _0074700 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Wireless-linked Return Function does not Operate  


DESCRIPTION

When the vehicle doors are unlocked through wireless unlock or entry unlock operation, the certification ECU (smart key ECU assembly) sends the key ID signal and smart memory call request signal to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the signal and the driver door is opened, the ECU sends the memory call command signal for the received key ID to each outer mirror control ECU assembly. On receiving the memory call command signal, each outer mirror control ECU assembly moves the mirror surface to the stored position.

PROCEDURE

1.CHECK MEMORY CALL FUNCTION (MEMORY REGISTRATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

After performing any of the following procedures to link the key and a switch, check the Data List to confirm that the key and switch have been linked.


f.

With the engine switch on (IG) and the driver door closed, press and hold the M1 or M2 switch. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code registration mode to allow a key to be linked to mirror surface memory position.

HINT:

If the memory switch is released before entering registration mode, the memory switch will not enter registration mode.



g.

When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds once (0.5 seconds).

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mem SW No. w/KeyID1 Switch linked with key ID1 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1
MEM SW2: M2 linked with key ID1
MEM SW3: M3 linked with key ID1*
-
Mem SW No. w/KeyID2 Switch linked with key ID2 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2
MEM SW2: M2 linked with key ID2
MEM SW3: M3 linked with key ID2*
-
Mem SW No. w/KeyID3 Switch linked with key ID3 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3
MEM SW2: M2 linked with key ID3
MEM SW3: M3 linked with key ID3*
-
Mem SW No. w/KeyID4 Switch linked with key ID4 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4
MEM SW2: M2 linked with key ID4
MEM SW3: M3 linked with key ID4*
-
Mem SW No. w/KeyID5 Switch linked with key ID5 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5
MEM SW2: M2 linked with key ID5
MEM SW3: M3 linked with key ID5*
-
Mem SW No. w/KeyID6 Switch linked with key ID6 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6
MEM SW2: M2 linked with key ID6
MEM SW3: M3 linked with key ID6*
-
Mem SW No. w/KeyID7 Switch linked with key ID7 NONE, MEM SW1, MEM SW2 or MEM SW3* NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7
MEM SW2: M2 linked with key ID7
MEM SW3: M3 linked with key ID7*
-

*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.


Body Electrical > Main Body > Data List
Tester Display
Mem SW No. w/KeyID1
Mem SW No. w/KeyID2
Mem SW No. w/KeyID3
Mem SW No. w/KeyID4
Mem SW No. w/KeyID5
Mem SW No. w/KeyID6
Mem SW No. w/KeyID7
50003 123 185,186,187,188,189,190,191
OK:

The Data List shows that the key ID has been linked to a switch (M1 or M2).



Result:
Proceed to
OK
NG



OK

2.CHECK MEMORY CALL FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Wireless Transmitter Memory Function does not Operate)

2.CHECK MEMORY CALL FUNCTION
a.

Perform a wireless door unlock operation and check that opening the driver door causes the following:

·

The buzzer sounds for 0.1 seconds.

·

The mirror surface position automatically moves to a stored position.


Result:
Result Proceed to
The memory call function does not operate together with wireless door unlock operation only. A
The memory call function does not operate together with entry unlock operation only. B
The memory call function does not operate at all. C




A

3.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

B

10.CHECK SMART ENTRY AND START SYSTEM (ENTRY FUNCTION)

C

17.CHECK MEMORY CALL FUNCTION
3.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check wireless door lock control operation.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock control operation is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK MEMORY AND SEAT RESTORING OPERATION (POWER SEAT CONTROL SYSTEM)

NG

4.CHECK MEMORY AND SEAT RESTORING OPERATION (POWER SEAT CONTROL SYSTEM)
a.

Check memory and seat restoring operation.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Memory and seat restoring operations are normal.



Result:
Proceed to
OK
NG



OK

5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

7.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)
5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY
a.

Replace the outer mirror control ECU assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK MEMORY CALL FUNCTION
6.CHECK MEMORY CALL FUNCTION
a.

Perform registration for memory call function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


b.

Perform a wireless door unlock operation and check that opening the driver door causes the following:

·

The buzzer sounds for 0.1 seconds.

·

The mirror surface position automatically moves to a stored position.


OK:

Memory call reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Courtesy SW Driver door courtesy switch condition ON or OFF ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed)
-
Body Electrical > Main Body > Data List
Tester Display
FL Door Courtesy SW
50003 123 199
OK:

ON or OFF appears on the intelligent tester.



Result:
Proceed to
OK
NG



OK

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

8.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK MEMORY CALL FUNCTION
9.CHECK MEMORY CALL FUNCTION
a.

Perform a wireless door unlock operation and check that opening the driver door causes the following:

·

The buzzer sounds for 0.1 seconds.

·

The mirror surface position automatically moves to a stored position.


OK:

Memory call reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.CHECK SMART ENTRY AND START SYSTEM (ENTRY FUNCTION)
a.

Check the smart entry and start system operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Smart entry and start system operation is normal.



Result:
Proceed to
OK
NG



OK

11.CHECK MEMORY AND SEAT RESTORING OPERATION (POWER SEAT CONTROL SYSTEM)

NG

11.CHECK MEMORY AND SEAT RESTORING OPERATION (POWER SEAT CONTROL SYSTEM)
a.

Check memory and seat restoring operation.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Memory and seat restoring operation is normal.



Result:
Proceed to
OK
NG



OK

12.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

14.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)
12.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY
a.

Replace the outer mirror control ECU assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK MEMORY CALL FUNCTION
13.CHECK MEMORY CALL FUNCTION
a.

Perform registration for memory call function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


b.

Perform a wireless door unlock operation and check that opening the driver door causes the following:

·

The buzzer sounds for 0.1 seconds.

·

The mirror surface position automatically moves to a stored position.


OK:

Memory call reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

14.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Courtesy SW Driver door courtesy switch condition ON or OFF ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed)
-
Body Electrical > Main Body > Data List
Tester Display
FL Door Courtesy SW
50003 123 199
OK:

ON or OFF appears on the intelligent tester.



Result:
Proceed to
OK
NG



OK

15.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

15.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK MEMORY CALL FUNCTION
16.CHECK MEMORY CALL FUNCTION
a.

Perform registration for memory call function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


b.

Perform a wireless door unlock operation and check that opening the driver door causes the following:

·

The buzzer sounds for 0.1 seconds.

·

The mirror surface position automatically moves to a stored position.


OK:

Memory call reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

17.CHECK MEMORY CALL FUNCTION
a.

Perform a wireless door unlock operation and check that opening the driver door causes the following:

·

The buzzer sounds for 0.1 seconds.

·

The mirror surface position automatically moves to a stored position.


OK:

Memory call reactivation function is normal.



Result:
Proceed to
OK
NG



OK

18.CHECK REACTIVATION FUNCTION

NG

22.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)
18.CHECK REACTIVATION FUNCTION
a.
B293945
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the engine switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.
B293946
0.163,0.114 0.333,0.256 0.17,0.142 10 *a
*a Turn to Right Fully


Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

OK:

Mirror function is normal.



Result:
Proceed to
OK
NG



OK

19.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

21.CHECK ELECTRICAL REMOTE CONTROL MIRROR FUNCTION
19.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY
a.

Replace the outer mirror control ECU assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.CHECK MEMORY CALL FUNCTION
20.CHECK MEMORY CALL FUNCTION
a.

Perform registration for memory call function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


b.

Perform a wireless door unlock operation and check that opening the driver door causes the following:

·

The buzzer sounds for 0.1 seconds.

·

The mirror surface position automatically moves to a stored position.


OK:

Memory call reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

21.CHECK ELECTRICAL REMOTE CONTROL MIRROR FUNCTION
a.

Check electrical remote control mirror function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Electrical remote control mirror function is normal.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

GO TO OTHER DIAGNOSIS PROCEDURE (PROBLEM SYMPTOMS TABLE)

22.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Courtesy SW Driver door courtesy switch condition ON or OFF ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed)
-
Body Electrical > Main Body > Data List
Tester Display
FL Door Courtesy SW
50003 123 199
OK:

ON or OFF appears on the intelligent tester.



Result:
Proceed to
OK
NG



OK

23.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

23.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

24.CHECK MEMORY CALL FUNCTION
24.CHECK MEMORY CALL FUNCTION
a.

Perform registration for memory call function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


b.

Perform a wireless door unlock operation and check that opening the driver door causes the following:

·

The buzzer sounds for 0.1 seconds.

·

The mirror surface position automatically moves to a stored position.


OK:

Memory call reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)