Key IDs can be registered (linked) with either the M1 or M2 seat memory switches. The key ID registration procedure should be performed while the electrical key transmitter is in the vehicle, the engine switch is on (IG), and the driver door is closed. When registration is completed, the buzzer will sound as an answerback.
Check the power door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Power door lock operation is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the smart entry and start system (entry function).
Smart entry and start system (entry function) is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Turn to Left Fully |
Turn the engine switch on (IG).
Using the outer mirror switch assembly, turn the mirror surface to the fully left position.
Press the M1 switch while the SET switch is being pressed.
Check that the buzzer sounds for 0.5 seconds and the mirror surface position is stored.
Using the outer mirror switch assembly, turn the mirror surface to the fully right position.
Press the M1 switch.
Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the stored fully left position.
| Result | Proceed to |
|---|---|
| Memory and reactivation function is normal | A |
| Memory function is not normal | B |
| Reactivation function is not normal | C |
A
B
C
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FL Door Courtesy SW | Driver door courtesy switch condition | ON or OFF | ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed) |
- |
| Tester Display |
|---|
| FL Door Courtesy SW |
ON or OFF appears on the screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
With the engine switch on (IG) and the driver door closed, press and hold the M1 or M2 switch. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code registration mode to allow a key to be linked to mirror surface memory position.
If the memory switch is released before entering registration mode, the memory switch will not enter registration mode.
When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds once (0.5 seconds).
The buzzer sounds when registration is completed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Body / Main Body / Data List.
After performing any of the following procedures to cut the link between the key and switch, check that the Data List for the applicable key changes to NONE.
With the engine switch on (IG) and the driver door closed, press and hold the SET switch. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code deletion mode.
If the memory switch is released before entering deletion mode, the memory switch will not enter deletion mode.
When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds twice (0.1 seconds each time).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mem SW No. w/KeyID1 | Switch linked with key ID1 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1 MEM SW2: M2 linked with key ID1 MEM SW3: M3 linked with key ID1* |
- |
| Mem SW No. w/KeyID2 | Switch linked with key ID2 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2 MEM SW2: M2 linked with key ID2 MEM SW3: M3 linked with key ID2* |
- |
| Mem SW No. w/KeyID3 | Switch linked with key ID3 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3 MEM SW2: M2 linked with key ID3 MEM SW3: M3 linked with key ID3* |
- |
| Mem SW No. w/KeyID4 | Switch linked with key ID4 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4 MEM SW2: M2 linked with key ID4 MEM SW3: M3 linked with key ID4* |
- |
| Mem SW No. w/KeyID5 | Switch linked with key ID5 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5 MEM SW2: M2 linked with key ID5 MEM SW3: M3 linked with key ID5* |
- |
| Mem SW No. w/KeyID6 | Switch linked with key ID6 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6 MEM SW2: M2 linked with key ID6 MEM SW3: M3 linked with key ID6* |
- |
| Mem SW No. w/KeyID7 | Switch linked with key ID7 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7 MEM SW2: M2 linked with key ID7 MEM SW3: M3 linked with key ID7* |
- |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
| Tester Display |
|---|
| Mem SW No. w/KeyID1 |
| Mem SW No. w/KeyID2 |
| Mem SW No. w/KeyID3 |
| Mem SW No. w/KeyID4 |
| Mem SW No. w/KeyID5 |
| Mem SW No. w/KeyID6 |
| Mem SW No. w/KeyID7 |
The Data List display for the applicable key changes to NONE.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
After performing any of the following procedures to link the key and a switch, check the Data List to confirm that the key and switch have been linked.
With the engine switch on (IG) and the driver door closed, press and hold the M1 or M2 switch. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code registration mode to allow a key to be linked to mirror surface memory position.
If the memory switch is released before entering registration mode, the memory switch will not enter registration mode.
When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly LH sounds once (0.5 seconds).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mem SW No. w/KeyID1 | Switch linked with key ID1 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1 MEM SW2: M2 linked with key ID1 MEM SW3: M3 linked with key ID1* |
- |
| Mem SW No. w/KeyID2 | Switch linked with key ID2 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2 MEM SW2: M2 linked with key ID2 MEM SW3: M3 linked with key ID2* |
- |
| Mem SW No. w/KeyID3 | Switch linked with key ID3 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3 MEM SW2: M2 linked with key ID3 MEM SW3: M3 linked with key ID3* |
- |
| Mem SW No. w/KeyID4 | Switch linked with key ID4 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4 MEM SW2: M2 linked with key ID4 MEM SW3: M3 linked with key ID4* |
- |
| Mem SW No. w/KeyID5 | Switch linked with key ID5 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5 MEM SW2: M2 linked with key ID5 MEM SW3: M3 linked with key ID5* |
- |
| Mem SW No. w/KeyID6 | Switch linked with key ID6 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6 MEM SW2: M2 linked with key ID6 MEM SW3: M3 linked with key ID6* |
- |
| Mem SW No. w/KeyID7 | Switch linked with key ID7 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7 MEM SW2: M2 linked with key ID7 MEM SW3: M3 linked with key ID7* |
- |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
| Tester Display |
|---|
| Mem SW No. w/KeyID1 |
| Mem SW No. w/KeyID2 |
| Mem SW No. w/KeyID3 |
| Mem SW No. w/KeyID4 |
| Mem SW No. w/KeyID5 |
| Mem SW No. w/KeyID6 |
| Mem SW No. w/KeyID7 |
Data List shows that the key ID has been linked to a switch (M1 or M2).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a wireless door unlock operation and check that opening the driver door causes the following:
The buzzer sounds for 0.1 seconds.
The mirror surface position automatically moves to a stored position.
Memory call reactivation function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Enter the following menus: Body / Driver Seat / Active Test.
Perform Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Buzzer | Buzzer built into the front power seat LH | ON or OFF | - |
| Tester Display |
|---|
| Buzzer |
The buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
After performing any of the following procedures to link the key and a switch, check the Data List to confirm that the key and switch have been linked.
With the engine switch on (IG) and the driver door closed, press and hold the M1 or M2 switch. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code registration mode to allow a key to be linked to mirror surface memory position.
If the memory switch is released before entering registration mode, the memory switch will not enter registration mode.
When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds once (0.5 seconds).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mem SW No. w/KeyID1 | Switch linked with key ID1 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1 MEM SW2: M2 linked with key ID1 MEM SW3: M3 linked with key ID1* |
- |
| Mem SW No. w/KeyID2 | Switch linked with key ID2 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2 MEM SW2: M2 linked with key ID2 MEM SW3: M3 linked with key ID2* |
- |
| Mem SW No. w/KeyID3 | Switch linked with key ID3 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3 MEM SW2: M2 linked with key ID3 MEM SW3: M3 linked with key ID3* |
- |
| Mem SW No. w/KeyID4 | Switch linked with key ID4 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4 MEM SW2: M2 linked with key ID4 MEM SW3: M3 linked with key ID4* |
- |
| Mem SW No. w/KeyID5 | Switch linked with key ID5 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5 MEM SW2: M2 linked with key ID5 MEM SW3: M3 linked with key ID5* |
- |
| Mem SW No. w/KeyID6 | Switch linked with key ID6 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6 MEM SW2: M2 linked with key ID6 MEM SW3: M3 linked with key ID6* |
- |
| Mem SW No. w/KeyID7 | Switch linked with key ID7 | NONE, MEM SW1, MEM SW2 or MEM SW3* | NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7 MEM SW2: M2 linked with key ID7 MEM SW3: M3 linked with key ID7* |
- |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
| Tester Display |
|---|
| Mem SW No. w/KeyID1 |
| Mem SW No. w/KeyID2 |
| Mem SW No. w/KeyID3 |
| Mem SW No. w/KeyID4 |
| Mem SW No. w/KeyID5 |
| Mem SW No. w/KeyID6 |
| Mem SW No. w/KeyID7 |
The Data List shows that the key ID has been linked to a switch (M1 or M2).
| Proceed to |
|---|
| OK |
| NG |
OK
NG