The TCM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the TCM compares the actual gear with the shift schedule in the TCM memory to detect mechanical problems of the shift solenoid valves and valve body.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0796 | Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) | The engine revs freely when 2nd or 6th gear is commanded (2-trip detection logic).
When the following is detected twice (2-trip detection logic): ·
When 1st gear is commanded, 2nd gear is engaged. |
·
Shift solenoid valve SL3 remains open or closed. ·
Valve body is blocked. ·
Automatic transaxle (clutch, brake or gear etc.) |
Comes on | DTC stored |
The TCM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft revolution (speed), intermediate (counter) shaft revolution (speed) and output shaft revolution (speed), the TCM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the TCM and the actual gear are not the same, the TCM illuminates the MIL and stores the DTC.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Trouble Codes.
Read the DTCs using the intelligent tester.
| Display (DTC Output) | Proceed to |
|---|---|
| Only "P0796" is output | A |
| "P0796" and other DTCs are output | B |
If a solenoid is stuck off, DTCs for several solenoids including the malfunctioning solenoid will be detected.
A
B
| *1 | Shift Solenoid Valve SL3 |
Remove shift solenoid valve SL3.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>REMOVAL
There are no foreign objects on each valve and they operate smoothly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE ASSEMBLY>COMPONENTS
NG
This test should always be performed with at least 2 people.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operates the shift solenoid valves to allow gears to selected manually. | ·
Press "→" button: Upshift occurs ·
Press "←" button: Downshift occurs |
Can be used to check the operation of the shift solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition] 50 km/h (31 mph) or less |
| Tester Display |
|---|
| Control the Shift Position |
This test can be conducted when the vehicle is stopped.
When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.
The gear commanded by the TCM is shown in the Data List / Shift Status display on the intelligent tester.
Check the vehicle speed and the gear when the engine speed is 1000 rpm.
Because the torque converter has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gear, however a difference of speed should still be evident following each gear change.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
|---|---|---|---|---|---|
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the TCM commanded gear and the actual gear.
| Actual Gear during Malfunction | TCM Commanded Gear | Proceed to | ||||||
|---|---|---|---|---|---|---|---|---|
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Shift solenoid SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | ||
| Shift solenoid SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | ||
| Shift solenoid SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | ||
| Shift solenoid SL4 | Stuck ON*3 | 3rd | 3rd | 3rd | 4th | 5th | 5th | D |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | ||
| Shift solenoid SLT | Stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E |
| Stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | ||
*1: Neutral
*2: If shift solenoid SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
*3: When shift solenoid SLT is stuck off, gear shifting is normal.
A
B
C
D
E