Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0778  Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)  


DESCRIPTION

Changing from 1st to 6th is performed by the TCM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (See page Drivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) The TCM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears. (1-trip detection logic)
·

Output signal duty equals to 100%.

(NOTE: SL2 output signal duty is less than 100% under normal condition.)


·

Open or short in shift solenoid valve SL2 circuit

·

Shift solenoid valve SL2

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL2 circuit. The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any of the shift solenoid valve circuits, the TCM detects the problem and illuminates the MIL and stores the DTC. The TCM also performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the TCM stops sending current to the circuit.)

While driving and shifting gears, if the TCM detects an open or short in the shift solenoid valve SL2 circuit, the TCM determines there is a malfunction (See page Drivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

WIRING DIAGRAM

C133261
5.698,0.5 6.063,0.833 0.365,0.333 10 TCM 1.99,3.844 3.365,4.271 1.375,0.427 10 Transaxle Assembly 5.094,1.865 5.635,2.031 0.542,0.167 10 SL2+ 5.865,1.073 6.406,1.24 0.542,0.167 10 +B 5.094,3.229 5.635,3.396 0.542,0.167 10 SL2- 1.604,2.354 3.656,2.74 2.052,0.385 10 Shift Solenoid Valve SL2

CAUTION / NOTICE / HINT

HINT:

The following table shows normal operation of the shift solenoid valve SL2 when the shift lever is in D:

TCM commanded gear 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL2 OFF OFF OFF ON ON ON


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SL2)
a.
C133212
2.332,1.153 2.686,1.302 0.355,0.149 10 SL2+ 2.34,0.291 2.672,0.44 0.332,0.149 10 SL2- 1.545,0.785 2.286,1.221 false 1.673,0.712 2.322,0.398 false 0.669,0.263 0.837,0.42 0.169,0.157 10 *a
*a Component without harness connected
(Transmission Wire)


Remove the TCM from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (SL2+) - 8 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
9 (SL2+) - Body ground and other terminals Always 10 kΩ or higher
8 (SL2-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT SHIFT SOLENOID VALVE SL2
2.INSPECT SHIFT SOLENOID VALVE SL2
a.
C201747C02
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.177,4.198 1.385,4.406 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.51,2.771 0.688,2.969 0.177,0.198 10 1 2.521,2.76 2.698,2.958 0.177,0.198 10 2 0.135,0.135 0.354,0.344 0.219,0.208 10 *1
*1 Shift Solenoid Valve SL2


Remove shift solenoid valve SL2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG