The power steering ECU assembly supplies current to the power steering motor assembly through the motor circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition |
|---|---|---|---|---|---|
| C1524/24 | Motor Circuit Malfunction | Short (or open) in motor circuit or abnormal voltage or current in motor circuit | ·
Power steering motor assembly ·
Power steering ECU assembly |
EPS Warning Light: Comes on | Ignition switch ON again |
| C1555/25 | Motor Relay Welding Failure | Motor relay circuit malfunction | ·
Power steering motor assembly ·
Power steering ECU assembly |
EPS Warning Light: Comes on | Ignition switch ON again |
If the power steering ECU assembly has been replaced, perform assist map writing (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).
Disengage the 4 claws to remove the protector.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING ECU>REMOVAL
Check that the motor terminal bolts are tightened to the specified torque.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING ECU>INSTALLATION
The motor terminal bolts are tightened to the specified torque.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Power Steering Motor Assembly |
Remove the power steering motor assembly.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c-1 (PHA) - c-2 (PHB) | 25°C (77°F) | 12.7 to 17.2 mΩ |
| c-2 (PHB) - c-3 (PHC) | 25°C (77°F) | 12.7 to 17.2 mΩ |
| c-3 (PHC) - c-1 (PHA) | 25°C (77°F) | 12.7 to 17.2 mΩ |
| c-1 (PHA) - Motor case | Always | 10 kΩ or higher |
| c-2 (PHB) - Motor case | Always | 10 kΩ or higher |
| c-3 (PHC) - Motor case | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Chassis / EMPS / Data List.
Select the items "Motor Terminal Volt (U)", "Motor Terminal Volt (V)" and "Motor Terminal Volt (W)" in the Data List and read the value displayed on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Motor Terminal Volt(U) | Motor terminal voltage (A phase) | Min.: 0.000 V
Max.: 98.000 V |
Engine running and steering wheel being turned: Value changes within 4 to 35 V range | - |
| Motor Terminal Volt(V) | Motor terminal voltage (B phase) | Min.: 0.000 V
Max.: 98.000 V |
Engine running and steering wheel being turned: Value changes within 4 to 35 V range | - |
| Motor Terminal Volt(W) | Motor terminal voltage (C phase) | Min.: 0.000 V
Max.: 98.000 V |
Engine running and steering wheel being turned: Value changes within 4 to 35 V range | - |
| Tester Display |
|---|
| Motor Terminal Volt(U) |
| Motor Terminal Volt(V) |
| Motor Terminal Volt(W) |
| Result | Proceed to |
|---|---|
| During steering operation, value changes within 4 to 35 V range. | A |
| During steering operation, voltage is not generated. | B |
A
B