Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2030EQ _55 Steering _014655 POWER ASSIST SYSTEMS _0077045 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1528/12  Motor Rotation Angle Sensor Malfunction  


DESCRIPTION

The motor rotation angle sensor detects the motor rotation angle and sends this information to the power steering ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1528/12 Motor Rotation Angle Sensor Malfunction Motor rotation angle sensor malfunction
·

Motor rotation angle sensor (built into power steering motor assembly)

·

Power steering ECU assembly


EPS Warning Light: Comes on Ignition switch ON again

WIRING DIAGRAM

C240263E08
4.26,0.625 4.667,0.865 0.406,0.24 10 false RZV1 4.271,1.208 4.698,1.458 0.427,0.25 10 false RZV2 4.271,1.74 4.917,1.958 0.646,0.219 10 false RZCS1 4.26,2.292 4.896,2.583 0.635,0.292 10 false RZSN1 4.25,2.854 4.875,3.125 0.625,0.271 10 false RZCS2 4.25,3.448 4.854,3.708 0.604,0.26 10 false RZSN2 4.26,4.115 6.344,4.281 2.083,0.167 10 false Power Steering ECU Assembly 4.26,3.917 4.604,4.083 0.344,0.167 10 false b 0.24,3.938 2.688,4.375 2.448,0.438 10 false Motor Rotation Angle Sensor (built into Power Steering Motor Assembly) 4.083,0.448 4.25,0.677 0.167,0.229 10 false 6 4.063,1.083 4.219,1.302 0.156,0.219 10 false 2 4.063,1.667 4.229,1.938 0.167,0.271 10 false 5 4.083,2.188 4.26,2.448 0.177,0.26 10 false 7 4.083,2.76 4.25,2.979 0.167,0.219 10 false 1 4.063,3.323 4.25,3.625 0.188,0.302 10 false 3

INSPECTION PROCEDURE

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connection condition of the motor rotation angle sensor connector.

OK:

Motor rotation angle sensor connector is securely connected to the power steering ECU assembly.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (MOTOR ROTATION ANGLE SENSOR)

NG

CONNECT CONNECTOR

2.READ VALUE USING INTELLIGENT TESTER (MOTOR ROTATION ANGLE SENSOR)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "Motor Rotation Angle" in the Data List and read the value displayed on the intelligent tester.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Motor Rotation Angle Motor rotation angle Min.: 0.000 deg
Max.: 1441.770 deg
Engine running and steering wheel being turned: During steering operation, motor rotation angle value changes from 0 to 360° -
Chassis > EMPS > Data List
Tester Display
Motor Rotation Angle
50003 142 18
OK:

During steering operation, motor rotation angle value changes from 0 to 360°.



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

3.CHECK POWER STEERING MOTOR ASSEMBLY (MOTOR ROTATION ANGLE SENSOR)
3.CHECK POWER STEERING MOTOR ASSEMBLY (MOTOR ROTATION ANGLE SENSOR)
a.
C238938C03
0.573,0.667 0.969,0.917 0.396,0.25 1.365,1.688 0.875,1.49 false 1.854,1.688 2.479,1.271 false 1.844,2 2.26,2.656 false 1.656,2.021 1.719,2.729 false 1.365,2.031 1.135,2.625 false 1.635,1.677 1.781,0.833 false 0.125,0.104 0.667,0.51 0.542,0.406 10 *a 0.719,0.698 1.292,1.167 0.573,0.469 10 b 2.073,2.698 2.844,3.052 0.771,0.354 10 RZSN1 0.385,1.396 1.271,1.813 0.885,0.417 10 RZCS2 0.854,2.656 1.458,2.948 0.604,0.292 10 RZCS1 1.542,2.76 2.26,3.156 0.719,0.396 10 RZV1 1.594,0.615 2.427,1.031 0.833,0.417 10 RZV2 2.531,1.188 3.219,1.594 0.688,0.406 10 RZSN2
*a Front view of wire harness connector
(to Motor Rotation Angle Sensor)


Disconnect the connector from the motor rotation angle sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b-6 (RZV1) - b-2 (RZV2) 25°C (77°F) 14.0 to 17.2 Ω
b-5 (RZCS1) - b-1 (RZCS2) 25°C (77°F) 25.8 to 31.6 Ω
b-7 (RZSN1) - b-3 (RZSN2) 25°C (77°F) 25.8 to 31.6 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE POWER STEERING MOTOR ASSEMBLY