Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2030EQ _55 Steering _014655 POWER ASSIST SYSTEMS _0077045 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551/25  IG Power Supply Voltage Malfunction  


DESCRIPTION

The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1551/25 IG Power Supply Voltage Malfunction IG power source circuit malfunction inside ECU
·

EPS-IG1 fuse

·

IG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


EPS Warning Light: Comes on Ignition switch ON again

WIRING DIAGRAM

C250100E28
0.26,1.031 1.698,1.25 1.438,0.219 10 false from IG1 NO. 3 Relay 2.208,1.167 3.104,1.521 0.896,0.354 10 false EPS-IG1 3.448,1.031 3.74,1.25 0.292,0.219 10 false Ij2 5.083,1.063 5.25,1.208 0.167,0.146 10 false IG 3.469,0.813 3.563,0.958 0.094,0.146 10 false 5 4.781,0.792 4.875,0.938 0.094,0.146 10 false 1 4.802,1.938 4.896,2.083 0.094,0.146 10 false 2 5.083,2.156 5.51,2.302 0.427,0.146 10 false PGND 4.854,2.896 6.979,3.177 2.125,0.281 10 false Power Steering ECU Assembly 4.792,1.042 5.021,1.302 0.229,0.26 10 false j1 4.792,2.135 5.063,2.385 0.271,0.25 10 false j2 4.146,1.177 4.365,1.448 0.219,0.271 10 false *1 3.531,2.24 3.76,2.448 0.229,0.208 10 false *1 0.292,3.271 2.479,3.552 2.188,0.281 10 false *1: ECU Wire Sub-assembly

INSPECTION PROCEDURE

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (IG POWER SUPPLY)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.READ VALUE USING INTELLIGENT TESTER (IG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "IG power supply" in the Data List and read the value displayed on the intelligent tester.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Power Supply ECU power source voltage Min.: 0.0000 V
Max.: 20.1531 V
Ignition switch ON: 9 to 16 V -
Chassis > EMPS > Data List
Tester Display
IG Power Supply
50003 142 11
OK:

The normal condition value is displayed on the intelligent tester.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
a.
C240359C03
0.458,0.458 0.906,0.74 0.448,0.281 2.531,1.083 2.156,1.219 false 0.135,0.083 0.604,0.458 0.469,0.375 10 *a 2.573,0.979 3.063,1.26 0.49,0.281 10 IG 0.604,0.521 0.938,0.927 0.333,0.406 10 Ij2
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the Ij2 connector from the ECU wire sub-assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Ij2-5 (IG) - Body ground Ignition switch ON 9 to 16 V



Result:
Proceed to
OK
NG



OK

4.CHECK ECU WIRE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240351C04
0.344,3.271 0.792,3.552 0.448,0.281 0.604,0.906 1.052,1.188 0.448,0.281 2.271,3.531 2.354,4.135 false 1.115,1.677 1.49,1.802 false 0.198,0.146 0.635,0.458 0.438,0.313 10 false *a 0.51,3.333 0.948,3.729 0.438,0.396 10 false j2 2.177,4.177 2.906,4.51 0.729,0.333 10 false PGND 0.917,1.583 1.344,1.948 0.427,0.365 10 false IG 0.771,0.969 1.156,1.354 0.385,0.385 10 false j1
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the Ij2 connector to the ECU wire sub-assembly.


b.

Disconnect the power steering ECU assembly j1 and j2 connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j1-1 (IG) - Body ground Ignition switch ON 9 to 16 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY