In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function(s) does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.
The wireless door lock control system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Utility / Customize / Wireless Door Lock.
Select the setting by referring to the table below.
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Hazard Answer Back | When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice. |
ON | 0:OFF,1:ON | Main body ECU (Multiplex network body ECU) |
| Wireless Buzzer Resp | Wireless door lock buzzer response | ON | 0:OFF,1:ON | Main body ECU (Multiplex network body ECU) |
| Wireless Buzzer Vol | Wireless door lock buzzer volume | Level 5 | 0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0 | Main body ECU (Multiplex network body ECU) |
| Result | Proceed to |
|---|---|
| Both items are ON and except Level 0 | A |
| Either item is OFF or Level 0 | B |
A
B
Check the wireless door lock control function using the electrical key transmitter sub-assembly.
| Result | Proceed to |
|---|---|
| Wireless door lock/unlock operates normally. | A |
| Wireless door lock/unlock does not operate normally. | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door RH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| RR-Door Lock Pos SW | Rear door RH and LH unlock detection switch signal | ON or OFF | ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked |
*1 |
| RL-Door Lock Pos SW | Rear door RH and LH unlock detection switch signal | ON or OFF | ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked |
*2 |
*1: When checking RR-Door Lock Pos SW, make sure to check it with the rear door LH locked.
*2: When checking RL-Door Lock Pos SW, make sure to check it with the rear door RH locked.
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
The intelligent tester should display as shown in the table according to door lock operation.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Driver door) | B |
| NG (for Front Passenger door) | C |
| NG (for Rear LH door) | D |
| NG (for Rear RH door) | E |
A
B
C
D
E
Check the wireless answer-back operation using the electrical key transmitter sub-assembly.
| Result | Proceed to |
|---|---|
| Only wireless door lock buzzer answer-back does not occur. | A |
| Only hazard warning light answer-back does not occur. | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not turn on/off. | A |
| Wireless door lock buzzer turns on/off. | B |
A
B
Disconnect the A15 wireless door lock buzzer and 3D instrument panel junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A15-1 - 3D-22 | Always | Below 1 Ω |
| A15-2 - Body ground | Always | Below 1 Ω |
| A15-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-22 - MB-21 (BZR) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the wireless door lock buzzer with a new one.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the wireless answer-back function.
Wireless answer-back function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the hazard warning light blinks when the hazard warning signal switch is pressed.
Hazard warning light signal is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG