The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door RH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| RR-Door Lock Pos SW | Rear door RH unlock detection switch signal | ON or OFF | ON: Rear door LH locked and rear door RH unlocked
ON: Rear door LH unlocked and rear door RH locked ON: Rear door LH and rear door RH unlocked OFF: Rear door LH and rear door RH locked |
- |
| RL-Door Lock Pos SW | Rear door LH unlock detection switch | ON or OFF | ON: Rear door LH locked and rear door RH unlocked
ON: Rear door LH unlocked and rear door RH locked ON: Rear door LH and rear door RH unlocked OFF: Rear door LH and rear door RH locked |
- |
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
| Result | Proceed to |
|---|---|
| OK | A |
| Front door unlock detection switch LH does not operate | B |
| Front door unlock detection switch RH does not operate | C |
| Rear door unlock detection switch LH or rear door unlock detection switch RH does not operate | D |
A
B
C
D
Remove the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
Front door lock with motor assembly LH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K1 front door lock with motor assembly LH connector.
Disconnect the I13 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-8 (LSSR) - I13-7 (LSFL) | Always | Below 1 Ω |
| K1-8 (LSSR) - Body ground | Always | 10 kΩ or higher |
| K1-7 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
Front door lock with motor assembly RH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J1 front door lock with motor assembly RH connector.
Disconnect the I13 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-7 (LSSR) - I13-18 (LSFR) | Always | Below 1 Ω |
| J1-7 (LSSR) - Body ground | Always | 10 kΩ or higher |
| J1-8 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear door lock with motor assembly LH.
Inspect the rear door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
Rear door lock with motor assembly LH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M1 rear door lock with motor assembly LH connector.
Disconnect the 3C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M1-6 (LSSR) - 3C-17 | Always | Below 1 Ω |
| M1-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| M1-9 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear door lock with motor assembly RH.
Inspect the rear door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
Rear door lock with motor assembly RH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L1 rear door lock with motor assembly RH connector.
Disconnect the 3A instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L1-6 (LSSR) - 3A-53 | Always | Below 1 Ω |
| L1-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| L1-9 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-17 - MB-5 (LSR) | Always | Below 1 Ω |
| 3A-53 - MB-5 (LSR) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG