Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM2030EQ _58 Vehicle Interior _014667 METER / GAUGE / DISPLAY _0074615 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Receiver Gauge Malfunction  


DESCRIPTION

In this circuit, the meter ECU receives engine coolant temperature signals from the ECM using the CAN communication system. The meter ECU displays an engine coolant temperature indication that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E143765E85
0.625,3.083 2.021,3.417 1.396,0.333 10 false ECM 2.927,3.156 3.021,3.344 0.094,0.188 10 false : 3.01,3.177 4.656,3.531 1.646,0.354 10 false CAN Communication Line 5.302,3.073 7.115,3.677 1.813,0.604 10 false Combination Meter Assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

HINT:

If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot SFI System.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WATER TEMPERATURE METER OPERATION)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WATER TEMPERATURE METER OPERATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Water Temperature Meter Operation Engine coolant temperature receiver gauge Low, Normal, High -
Body Electrical > Combination Meter > Active Test
Tester Display
Water Temperature Meter Operation
50004 122 89
OK:

Engine coolant temperature receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK SFI SYSTEM

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK SFI SYSTEM
a.

Check if SFI system DTCs are output.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

4.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP, COOLANT TEMPERATURE)

B

4.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP, COOLANT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus:

i.

for Engine and ECT: Powertrain / Engine and ECT / Data List.


ii.

for Combination Meter: Body / Combination Meter / Data List.



e.

Check the values by referring to the table below.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temp Coolant temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) 75 to 100°C (167 to 212°F): After warming up
·

Stored as Freeze Frame Data

·

This is the engine coolant temperature.


Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature -40 to 140°C (-40 to 284°F) After warming up: 75 to 100°C (167 to 212°F)
·

If -40°C (-40°F): Sensor circuit open


·

If 140°C (284°F) or more: Sensor circuit shorted


HINT:
·

After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.

·

If the value is -40°C (-40°F), or 135°C (275°F), the sensor circuit is open or shorted.

·

Check if the engine overheats when the value indicates 135°C (275°F).



Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 234 8
Body Electrical > Combination Meter > Data List
Tester Display
Coolant Temperature
50003 122 10

Result:
Result Proceed to
The data list values of the ECUs match. A
The data list values of the ECUs do not match. B


HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.




A

REPLACE COMBINATION METER ASSEMBLY

B