If a malfunction is detected in the power supply circuit, the skid control ECU stores this DTC and the fail-safe function prohibits ABS operation.
This DTC is stored when the +BS terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.
The DTC is canceled when the +BS terminal voltage returns to normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1241 | Low Power Supply Voltage Malfunction | Any of the following is detected:
1.
The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (soft low voltage) is less than 9.6 V for 1 second or more. 2.
The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (hard low voltage) is less than 6.9 V for 1 second or more. 3.
The vehicle speed is 15 km/h (9 mph) or more, the +BS terminal voltage is 9.6 V or more, the skid control ECU turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold. (The skid control ECU monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU determines that the wiring resistance at the +BS terminal exceeds the standard resistance.) 4.
The +BS terminal voltage is less than 6.7 V and the skid control ECU judges that power supply voltage is abnormal for 0.06 seconds or more. |
·
ABS NO. 2 fuse ·
Battery ·
Charging system ·
Power source circuit ·
Ground circuit ·
Internal power supply circuit of the skid control ECU |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check the battery voltage.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A49 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-25 (+BS) - Body ground | Always | 11 to 14 V |
| A49-25 (+BS) - A49-38 (GND1) | Always | 11 to 14 V |
| A49-28 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| A49-28 (IG1) - A49-38 (GND1) | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for +BS circuit) | B |
| NG (for IG1 circuit) | C |
A
B
C
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-38 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A49 skid control ECU connector.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1241 is not output. | A |
| DTC C1241 is output. | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Disconnect the 1I engine room relay block and junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-25 (+BS) - 1I-1 | Always | Below 1 Ω |
Even if the resistance between the skid control ECU and the engine room relay block and junction block assembly is normal, there may be an abnormality in the resistance of the wiring between the battery and the engine room relay block and junction block assembly. Therefore, be sure to inspect the circuit between the battery and the engine room relay block and junction block assembly before replacing the skid control ECU (brake actuator assembly).
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG