Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1381  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

This DTC is stored when the skid control ECU receives a sensor supply voltage malfunction signal from the yaw rate and acceleration sensor (airbag sensor assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1381 Acceleration Sensor Power Supply Voltage Malfunction Vehicle speed is 6 km/h (4 mph) and yaw rate and acceleration sensor power supply malfunction signal is received for 1.1 seconds or more.
·

Yaw rate and acceleration sensor power source circuit

·

Yaw rate and acceleration sensor (Airbag sensor assembly)



WIRING DIAGRAM

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C239271C10
0.25,0.708 0.729,1 0.479,0.292 1.042,2.177 0.573,2.792 false 0.417,0.781 0.854,1.104 0.438,0.323 10 I47 0.24,0.219 0.667,0.781 0.427,0.563 10 *a 0.385,2.823 0.677,3 0.292,0.177 10 IG2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the I47 yaw rate and acceleration sensor (airbag sensor assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I47-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C239271C11
0.25,0.708 0.729,1 0.479,0.292 1.688,2.177 1.198,2.813 false 1.813,2.177 2.271,2.813 false 0.406,0.781 0.917,1.344 0.51,0.563 10 I47 0.229,0.219 0.635,0.719 0.406,0.5 10 *a 1.052,2.844 1.427,3.135 0.375,0.292 10 E1 2.208,2.844 2.552,3.229 0.344,0.385 10 E2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-25 (E1) - Body ground Always Below 1 Ω
I47-26 (E2) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)