Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1249  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU receives stop light switch signals and uses them to determine whether or not the brakes are applied.

DTCs may be stored if one of the following occurs:

·

Stop light switch stuck on malfunction.

·

Accelerator and brake pedals depressed simultaneously.*


HINT:

*: The skid control ECU may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1249 Open in Stop Light Switch Circuit The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.09 kgf/cm2, 72 psi) or less, and the stop light switch is on for 60 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C239818E07
5.5,3.781 6,4.021 0.5,0.24 10 A49 5.5,3.948 7.031,4.417 1.531,0.469 10 Skid Control ECU (Brake Actuator Assembly) 5.969,1.125 6.396,1.49 0.427,0.365 10 STP 5.698,1.021 6.063,1.427 0.365,0.406 10 30 2.49,1.49 2.979,1.813 0.49,0.323 10 A33 2.469,1.635 3.583,2.135 1.115,0.5 10 Stop Light Switch Assembly 2.385,1 2.615,1.167 0.229,0.167 10 2 3.458,1 3.688,1.167 0.229,0.167 10 1 1.698,1.292 2.323,1.573 0.625,0.281 10 STOP 0.198,1.135 1.208,1.542 1.01,0.406 10 from Battery 1.813,2.656 3.26,3.031 1.448,0.375 10 to Stop Light Circuit 5.969,2.875 6.448,3.198 0.479,0.323 10 GND1 5.688,2.729 6.031,2.99 0.344,0.26 10 38

PROCEDURE

1.CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION
a.

Interview the customer to check if the pedals were depressed simultaneously while driving or braking.

OK:

The pedals were not depressed simultaneously.


HINT:

The skid control ECU may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously.

If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.



Result:
Proceed to
OK
NG



OK

2.CHECK STOP LIGHT OPERATION

NG

END

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays on or off according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
4.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1249 is not output. A
DTC C1249 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C238832C18
0.208,0.719 0.688,1.042 0.479,0.323 1.542,1.521 2.188,0.792 false 0.281,0.198 0.625,0.635 0.344,0.438 10 *a 0.333,0.802 0.75,1.135 0.417,0.333 10 A49 2.052,0.594 2.375,0.75 0.323,0.156 10 STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A49 skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
A49-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C173882C03
0.365,0.979 0.833,1.302 0.469,0.323 0.333,0.25 0.656,0.604 0.323,0.354 10 *a 0.49,1.063 0.917,1.448 0.427,0.385 10 A33
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Check that the STOP (7.5 A) fuse is normal.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A33 stop light switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

7.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
C239673C03
0.338,0.37 0.564,0.54 0.226,0.17 10 *a 1.941,1.855 2.415,1.068 false 1.659,1.855 1.184,1.068 false 2.401,0.851 2.571,1.021 0.17,0.17 10 1 1.077,0.851 1.233,1.021 0.156,0.17 10 2
*a Component without harness connected
(Stop Light Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin free Below 1 Ω
1 - 2 Switch pin pushed in 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C238832C17
0.208,0.719 0.688,1.042 0.479,0.323 1.542,1.521 2.188,0.792 false 0.271,0.198 0.469,0.354 0.198,0.156 10 *a 0.323,0.802 0.771,1.031 0.448,0.229 10 A49 2.156,0.583 2.51,0.896 0.354,0.313 10 STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Reconnect the A33 stop light switch assembly connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A49 skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
A49-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

9.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

9.RECONFIRM DTC
a.

Reconnect the A49 skid control ECU connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1249 is not output. A
DTC C1249 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

B