This DTC is stored if the navigation ECU sub-assembly judges that the signals or signal lines between the navigation ECU sub-assembly and the rear television camera assembly are not normal as a result of its self check.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1622 | Back Camera Disconnected | Open or short in the rear television camera assembly signal circuit | ·
Harness or connector ·
Rear television camera assembly ·
Navigation ECU sub-assembly |
When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION
Disconnect the I66 connector from the navigation ECU sub-assembly.
Disconnect the T6 connector from the rear television camera assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I66-16 (V-) - T6-2 (CV-) | Always | Below 1 Ω |
| I66-8 (V+) - T6-3 (CV+) | Always | Below 1 Ω |
| I66-15 (CGND) - T6-5 (CGND) | Always | Below 1 Ω |
| I66-7 (CA+) - T6-6 (CB+) | Always | Below 1 Ω |
| I66-16 (V-) - Body ground | Always | 10 kΩ or higher |
| I66-8 (V+) - Body ground | Always | 10 kΩ or higher |
| I66-15 (CGND) - Body ground | Always | 10 kΩ or higher |
| I66-7 (CA+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Navigation ECU Sub-assembly) |
Reconnect the I66 connector to the navigation ECU sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I66-16 (V-) - Body ground | Always | Below 1 Ω |
| I66-15 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I66-7 (CA+) - I66-15 (CGND) | Engine switch on (IG)
Shift lever in R |
5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the T6 connector to the rear television camera assembly.
| *a | Component with harness connected
(Navigation ECU Sub-assembly) |
| *a | Waveform 1 (camera lens is not covered, displaying an image) |
| *b | Waveform 2 (camera lens is covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
Reconnect the I66 and I64 connectors to the navigation ECU sub-assembly.
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation ECU sub-assembly with the connector connected.
Waveform is as shown in the illustration.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | I66-8 (V+) - I64-7 (GND1) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Engine switch on (IG), shift lever in R |
The video waveform changes according to the image sent by the rear television camera assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG