The navigation ECU sub-assembly receives luggage compartment door lock assembly open/close signals from the main body ECU (multiplex network body ECU) via CAN communication. When the luggage compartment door is open, the camera aiming cannot be adjusted correctly because the rear television camera assembly is installed on the luggage compartment door. Therefore, when adjusting the camera aiming calibration while the back door is open, a back door open warning message will be displayed on the screen and camera aiming adjustment will be canceled.
Check the parking assist monitor screen display mode settings. (Check if the parking guide lines are set to off.)
The luggage compartment door lock assembly is connected to the main body ECU (multiplex network body ECU) by the vehicle wire harness.
When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Luggage Courtesy SW | Luggage courtesy switch signal | ON or OFF | ON: Luggage compartment door open
OFF: Luggage compartment door closed |
- |
| Tester Display |
|---|
| Luggage Courtesy SW |
The luggage compartment door courtesy switch functions as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Luggage Compartment Door Lock Assembly) |
| *b | Close (Lock) |
| *c | Open (Unlock) |
Check operation of the door courtesy switch.
Measure the resistance according to the value(s) in the table below.
| Measurement Condition | Switch Condition | Specified Condition |
|---|---|---|
| 2 (E) - 3 (D+) | Close (Lock) | 10 kΩ or higher |
| 2 (E) - 3 (D+) | Open (Unlock) | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T3 luggage compartment door lock assembly connector.
Disconnect the 3C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T3-3 (D+) - 3C-9 | Always | Below 1 Ω |
| T3-3 (D+) - Body ground | Always | 10 kΩ or higher |
| T3-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-9 - MB-4 (LGCY) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG