Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation ECU sub-assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation ECU sub-assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



DTC No. Detection Item DTC Detection Condition Trouble Area
B15C2 Speed Signal Malfunction A difference between the GPS speed and SPD pulse is detected.
·

Navigation ECU sub-assembly

·

Combination meter assembly

·

Harness or connector

·

Junction connector



WIRING DIAGRAM

E237385E01
0.46,1.382 1.582,1.533 1.123,0.151 10 Skid Control ECU 0.867,0.583 1.158,0.734 0.292,0.151 10 SP1 0.153,1.382 0.472,1.563 0.319,0.181 10 A49 1.207,0.583 1.393,0.731 0.187,0.148 10 2 0.119,2.737 3.204,2.901 3.084,0.164 10 Certification ECU (Smart Key ECU Assembly)*5 0.119,2.584 0.410,2.748 0.290,0.164 10 I78 1.637,2.338 2.037,2.492 0.400,0.154 10 SPD 2.108,2.334 2.288,2.492 0.180,0.159 10 27 2.93,2.334 3.110,2.492 0.180,0.159 10 21 3.941,2.334 4.121,2.492 0.180,0.159 10 18 5.418,0.564 5.722,0.713 0.304,0.150 10 8 5.419,2.348 5.695,2.498 0.275,0.150 10 9 5.589,0.662 5.787,0.812 0.198,0.150 10 SI 5.583,2.446 5.784,2.597 0.201,0.151 10 +S 5.009,2.779 5.341,2.925 0.332,0.145 10 I18 5.285,2.779 7.120,2.972 1.835,0.193 10 Combination Meter Assembly 4.532,7.493 4.798,7.656 0.265,0.164 10 I72 4.843,7.493 7.156,7.811 2.312,0.318 10 Windshield Wiper Relay Assembly*4 5.633,7.186 6.046,7.340 0.413,0.154 10 SPD 2.938,3.769 3.117,3.927 0.180,0.159 10 19 3.948,3.769 4.128,3.927 0.180,0.159 10 17 5.368,7.102 5.551,7.261 0.183,0.159 10 24 3.96,7.102 4.143,7.261 0.183,0.159 10 20 2.942,7.102 3.125,7.261 0.183,0.159 10 16 2.102,7.108 2.305,7.270 0.203,0.162 10 10 5.303,5.115 5.520,5.277 0.217,0.162 10 17 1.164,7.472 1.441,7.625 0.277,0.153 10 A25 1.486,7.472 1.897,7.648 0.411,0.176 10 ECM 4.416,5.654 6.995,6.020 2.579,0.366 10 Navigation ECU Sub-assembly*2 or Radio and Display Receiver Assembly*3 2.36,8.256 4.754,8.419 2.394,0.163 10 *5: w/ Smart Entry and Start System 0.324,8.256 2.000,8.416 1.675,0.159 10 *4: w/ Auto Wiper System 4.815,7.933 6.722,8.115 1.907,0.182 10 *3: for Radio and Display Type 1.622,7.108 1.950,7.253 0.328,0.145 10 SPD 2.116,5.209 2.319,5.370 0.203,0.162 10 3 1.274,5.584 1.717,5.737 0.443,0.153 10 E7 1.5,5.584 1.911,5.760 0.411,0.176 10 TCM 1.636,5.209 1.964,5.354 0.328,0.145 10 SPD 5.595,5.222 5.924,5.367 0.328,0.145 10 SPD 5.595,3.792 5.924,3.938 0.328,0.145 10 SPD 5.249,5.293 5.568,5.439 0.318,0.145 10 I155 5.314,5.494 5.504,5.640 0.190,0.145 10 *3 4.946,5.115 5.162,5.277 0.217,0.162 10 17 4.934,5.293 5.209,5.439 0.275,0.145 10 I67 4.951,5.494 5.136,5.640 0.185,0.145 10 *2 2.118,3.782 2.429,3.943 0.311,0.162 10 11 0.602,4.155 0.877,4.308 0.275,0.153 10 I69 5.333,3.792 5.644,3.954 0.311,0.162 10 17 4.998,4.166 5.537,4.325 0.539,0.159 10 I150 0.91,4.155 2.411,4.518 1.501,0.363 10 Stereo Component Amplifier Assembly*2 5.335,4.166 7.089,4.341 1.754,0.176 10 Radio Receiver Assembly*1 1.719,3.85 2.047,3.995 0.328,0.145 10 SPD 2.445,7.933 4.482,8.115 2.037,0.182 10 *2: for Navigation Receiver Type 0.324,7.933 2.114,8.102 1.789,0.169 10 *1: for Radio Receiver Type 3.101,7.521 4.320,7.683 1.220,0.162 10 Junction Connector 2.789,7.521 3.190,7.684 0.401,0.164 10 I124

PROCEDURE

1.CHECK VEHICLE SENSORS (OPERATION CHECK)
a.
E176549

Enter the "Vehicle Sensors" screen. Refer to Check GPS & Vehicle Sensors in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "Vehicle Sensors" screen is almost the same as the actual vehicle speed measured using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E265641C07
1.438,0.25 1.844,0.51 0.406,0.26 0.938,1.906 1.344,1.313 false 0.146,0.104 0.458,0.302 0.313,0.198 10 *a 1.552,0.302 1.865,0.5 0.313,0.198 10 I18 0.833,1.927 1.146,2.125 0.313,0.198 10 +S 1.01,4.219 1.615,4.521 0.604,0.302 10 (A) 2.698,3.865 3.302,4.167 0.604,0.302 10 GND
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal I18-9 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I18-9 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION ECU SUB-ASSEMBLY

NG

3.INSPECT NAVIGATION ECU SUB-ASSEMBLY
a.

Check the input waveform.

E274958C02
1.75,0.323 2.125,0.573 0.375,0.25 2.688,1.927 2.469,1.427 false 0.344,0.229 0.656,0.427 0.313,0.198 10 false *a 1.854,0.354 2.313,0.552 0.458,0.198 10 false I67 2.573,1.958 3.031,2.156 0.458,0.198 10 false SPD 6.188,1.438 6.646,1.635 0.458,0.198 10 false GND 4.76,1.698 5.219,1.896 0.458,0.198 10 false (A)
*1 Component with harness connected
(Navigation ECU Sub-assembly)
- -


i.

Remove the navigation ECU sub-assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal I67-17 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I67-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the navigation ECU sub-assembly connector.


b.

Disconnect the junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-17 (SPD) - I124-17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - JUNCTION CONNECTOR)