This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit. | ·
Harness or connector ·
Speaker ·
Stereo component amplifier assembly*1 ·
Navigation ECU sub-assembly*2 |
*1: for 10 Speakers
*2: for 6 Speakers
for 6 Speakers
for 10 Speakers
Choose the model to be inspected.
| Model | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 10 Speakers | B |
A
B
Disconnect the connectors from the navigation ECU sub-assembly and speakers.
Measure the resistance between the navigation ECU sub-assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I64-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I64-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| I64-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I64-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| I65-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| I65-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| I65-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| I65-6 (RL-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I83-3 (+) - Body ground | Always | 10 kΩ or higher |
| I83-1 (-) - Body ground | Always | 10 kΩ or higher |
| I1-3 (+) - Body ground | Always | 10 kΩ or higher |
| I1-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J5-1 - J5-2 | Always | 3.2 to 4.8 Ω |
| K5-1 - K5-2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I83-2 (TWR-) - I83-4 (TWR+) | Always | 10 kΩ or higher |
| I83-1 (-) - I83-2 (TWR-) | Always | Below 1 Ω |
| I83-3 (+) - I83-4 (TWR+) | Always | Below 1 Ω |
| I1-2 (TWL-) - I1-4 (TWL+) | Always | 10 kΩ or higher |
| I1-1 (-) - I1-2 (TWL-) | Always | Below 1 Ω |
| I1-3 (+) - I1-4 (TWL+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the malfunction disappears when a known good speaker is installed.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Rear Speaker Assembly) |
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O18-1 - O18-2 | Always | 3.2 to 4.8 Ω |
| O21-1 - O21-2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the stereo component amplifier assembly and speakers.
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I68-15 (FR+) - Body ground | Always | 10 kΩ or higher |
| I68-30 (FR-) - Body ground | Always | 10 kΩ or higher |
| I68-11 (FL+) - Body ground | Always | 10 kΩ or higher |
| I68-26 (FL-) - Body ground | Always | 10 kΩ or higher |
| I68-12 (TWR+) - Body ground | Always | 10 kΩ or higher |
| I68-27 (TWR-) - Body ground | Always | 10 kΩ or higher |
| I68-14 (TWL+) - Body ground | Always | 10 kΩ or higher |
| I68-29 (TWL-) - Body ground | Always | 10 kΩ or higher |
| I68-13 (CTR+) - Body ground | Always | 10 kΩ or higher |
| I68-28 (CTR-) - Body ground | Always | 10 kΩ or higher |
| I68-10 (SR+) - Body ground | Always | 10 kΩ or higher |
| I68-25 (SR-) - Body ground | Always | 10 kΩ or higher |
| I68-9 (SL+) - Body ground | Always | 10 kΩ or higher |
| I68-24 (SL-) - Body ground | Always | 10 kΩ or higher |
| I68-8 (WF1+) - Body ground | Always | 10 kΩ or higher |
| I68-23 (WF1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J5-1 - J5-2 | Always | 4.6 to 6.6 Ω |
| K5-1 - K5-2 | Always | 4.6 to 6.6 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I84-4 - I84-3 | Always | 3.4 to 5.2 Ω |
| I2-4 - I2-3 | Always | 3.4 to 5.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Front No. 3 Speaker Assembly) |
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I60-1 - I60-2 | Always | 6.8 to 10.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Rear No. 2 Speaker Assembly) |
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O19-1 - O19-2 | Always | 6.8 to 10.2 Ω |
| O20-1 - O20-2 | Always | 6.8 to 10.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Rear Speaker Assembly) |
Resistance check
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O22-1 - O22-2 | Always | 4.8 to 6.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG