The navigation ECU sub-assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the navigation ECU sub-assembly and stereo component amplifier assembly, this DTC will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15D3 | Stereo Component Amplifier Disconnected | When either condition below is met:
·
Stereo component amplifier assembly is/was not connected while the ignition switch is ON or ACC. ·
Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started. |
·
Stereo component amplifier assembly power source circuit ·
AVC-LAN circuit between navigation ECU sub-assembly and stereo component amplifier assembly ·
Stereo component amplifier assembly ·
Navigation ECU sub-assembly ·
Harness or connector |
Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
The navigation ECU sub-assembly is the master unit.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.
| Result | Proceed to |
|---|---|
| DTC B15C3 is not output. | A |
| DTC B15C3 is output. | B |
A
B
Check that optional components (including associated wiring) which generate radio waves are not installed.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed. | A |
| Optional components (including associated wiring) are not installed. | B |
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the stereo component amplifier assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I68-3 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I68-1 (+B) - I68-3 (GND) | Always | 11 to 14 V |
| I69-12 (ACC) - I68-3 (GND) | Ignition switch ACC | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the navigation ECU sub-assembly connector.
Disconnect the stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I67-7 (TX1+) - I69-8 (TX+) | Always | Below 1 Ω |
| I67-8 (TX1-) - I69-7 (TX-) | Always | Below 1 Ω |
| I67-7 (TX1+) - Body ground | Always | 10 kΩ or higher |
| I67-8 (TX1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the stereo component amplifier assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG